PER5502BAT Maytag Range - Instructions

I took the back panel off, removed the old lens, installed the new lens. How easy to order from home, receive the part, do the repair and pay less than it costs to simply drive to the parts house. Cool....

Spoke to your very helpful staff, who advised me that a likely problem was the oven sensor. I took a chance and ordered the part, which came promptly. Your service video for the part was most helpful in my decision to try the part. Installation was a breeze, but it was the oven controller board that had failed and not the oven sensor. ... Read more That called for a service professional, who ultimately fixed the problem. Your service though, was excellent and I would highly recommend you to others.

Fastest, easiest thing I have ever done! I got my orders so fast it was unreal! Hurrah for good old American know-how. I will always recommend these good people!

It is very easy shut off the power yo the stove at the fuse box, unscrew the two screws and pull the element out replace and screw back into place.

The sensor is mounted in the top right side of the oven.An extra long screw driver helps to avoid damage to the sensor when replacing it.The connectors were the opposite to the old sensor and I did not see that there were adapter cables included. It might help to connect or tie these together as I only expected the sensor and did not loo ... Read more k for adapters.I had cut the wires and used wire nuts when I found the adapters.The repairs works fine.
Mike

I got the wiring diagram for the oven online.

I turned off the power and removed the screws on th out sides of the top of the oven (at the control panel) and the screws underneath the front of the control panel (one on each side toward the outside)

I found where power to the oven and broiler elements would be applied ... Read more .

I verified continuity through the elements, and that voltage was available to the control board.

I then found that voltage was not applied to the elements when they were turned on.

I verified that the thermocouple controlling temperature worked by measuring the output voltage and verifying that it increased when the thrermocouple was heated with a hair dryer.

Since all the inputs to the board (known as "Clock w/Overlay") were good, the board must be bad.

I ordered the board (partselect had the best price).

I removed the four screws holding the board, and removed the push on wiring connections.

I reversed the above process for re-assembly. The only slight complication was that the new board had one additional connection point available that was not on the old board. You don't use it. The new board fits a couple different models.

Turned the power on, then the oven on, then the broiler on, everything worked.

Success!

First I called a repairman and left a message. That was 3 weeks ago. So, I 'googled' the error message and determined what part I thought I needed. Ordered the part on Wednesday evening and it was there when I got home from work on Friday. I unpacked the part, got a phillips screwdriver and then watched the repair video on your websit ... Read more e. About 20 minutes later I pushed my stove back in place and the flashing said 'set time'. Then I checked both ovens, and have since used both, and everything works!!

Removed the two screws holding the sensor to the rear oven wall. pulled out sensor wire. It was caught on other wires behind the oven. removed the three screws holding the 8" inspection plate in the center of the rear panel. Carefully move the insulation and reach in to grasp the back end of the sensor wire. Once free from the snag it eas ... Read more ily pulls out with the sensor just as stated in the video. using the appropriate adaptor it was easy to re-asseble and and attach to the oven wall. Replace the rear panel with the three screws and it was done

Removed front panel of range, removed switch (2 screws), unclipped wires from back of existing switch. Installed new switch - reverse order of above.

I reoved old drip pans and installed new ones. Very easy, they look great!

Turned oven circuit breaker off. Removed oven racks. Removed 2 screws from old element. Pulled element out slightly disconnected wires on each end and reattached to new element. Pushed back in and reinstalled the 2 screws, reinstalled oven racks and turned circuit breaker back on. All done in about 20 minutes.

I switched the oven sensor easily enough, but it did not remedy the problem, so we are in the process of replacing the oven since it's about 20 yrs. old.

super easy after watching the how to video you had on it and iam the wife not the husband it was so easy thanks

Turned the power off to the oven, unscrewed the ends of the element, connected new element, screwed it back in to place and turned the powe back on. The video provided in my shipping confirmation was very helpful.

I unplugged the cord to the stove. Then I removed the two screws on the broken heating element. Once the screws were removed, I slid off the two wires attached to the element prones. Grab the new element and attached the two wires. Reinstalled screws. Plugged in the cord, and turned on oven. Heating element came on.