PE550 (Type 3) Weed Eater Edger - Parts

This Genuine OEM fuel filter is designed to maintain the performance and longevity of your equipment by preventing dirt and debris from entering the carburetor. Located inside the fuel tank, this essential component ensures clean fuel delivery, protecting the engine from potential damage caused by contaminants. Sold individually, the filt...Read moreer is built to meet original equipment standards for fit and function. Over time, the filter may become clogged, restricting fuel flow and making engine starts more difficult. For optimal performance, it should be replaced—not cleaned—at the first sign of blockage or wear.

This Fuel Line is a 25-inch, clear, plastic line used to deliver fuel. It requires a screwdriver, pliers, socket set, and nut driver and is rated as "Easy" to install by customers. If the fuel line wear out to the point of breaking, cracks and/or leaking will appear and the part should be replaced. Refer to your make, model and diagram to ensure this is the correct part for you.

These Weed Eater Blades are 8-3/8 x 1-1/2 inch black, metal blades which come individually sold and attach to the output shaft. Installation requires a wrench set and socket set, and is rated as "Easy". This blade is used for edging the grass around walkways and driveways. If the blade hits pavement it may break, and you will notice a vib...Read moreration or poor trimming, and the part must be replaced. Refer to your make model, and diagrams to ensure you're choosing the correct part.

The Fuel Cap with retainer, often simply known just as the fuel cap, keeps fuel from splashing out of your tank and debris from entering it. Black in color, it is sold individually and made of plastic. Because of everyday fatigue and wear, the cap can become damaged over time and must be replaced. You will know if it is time to replace ...Read moreyour fuel cap if you notice visible damage or experience fuel leaking from it. You can make this repair by hand, just attach the cap directly back onto the fuel tank. Most of our customers found this repair very easy.

This OEM Piston Ring is used to provide a seal between the piston and cylinder wall. It attaches around the piston, inside the groove. It will require a screwdriver, allen wrench, torx wrench and socket set and is rated as "Hard" to install. The part is silver, metal, and individually sold. If broken due to general wear/fatigue you will h...Read moreave poor compression within the cylinder, causing a loss of power. If broken, damaged or worn, the part should be replaced. Refer to your make, model, and diagram to ensure this is the correct part.

This is an authentic OEM replacement kit for use with lawn and garden equipment. Each kit includes the carburetor, cylinder, crankcase, and muffler gaskets. The carburetor gasket seals the area between the carburetor and engine block to prevent the entry of contaminants into the carburetor. The crankcase gasket prevents oil from leaking o...Read moreut of the crankcase. The cylinder and muffler gaskets prevent the combustion and exhaust gases from escaping. If you are experiencing common problems such as leaking, loss of compression, and poor engine performance this indicates that your gaskets may be worn down or damaged and need replacement. Carefully remove the old gaskets and thoroughly clean the mating surfaces where the new gaskets will be installed to ensure a good seal. Install the new gaskets and ensure that they fit properly.

This flywheel is an authentic manufacturer replacement part for use with lawn and outdoor equipment. The flywheel is a heavy, circular disc that has magnets that create an electric charge sent to the spark plug to create the spark that ignites the fuel and air mixture in the engine. It is attached to the engine crankshaft by a key known a...Read mores a shear pin or flywheel key. This assembly is a critical component in the starting and running of your power equipment. Over time, the magnets on the flywheel will wear down, and the flywheel may chip and crack. A faulty flywheel will result in a loss of power, excessive shaking during use, and difficulty starting the equipment. Remove the flywheel using a flywheel puller. Position the new flywheel on the crankshaft and secure it with the retaining nut and flywheel key. This flywheel is sold as an individual replacement part.

This replacement fuel tank assembly is a genuine OEM sourced item. It is specially designed for use with Weed Eater gas powered string trimmers and edgers. This assembly includes a plastic fuel tank, fuel lines, fuel cap and the screws to secure it. To complete this repair you will need a screwdriver.

This is an original part from Craftsman for edgers and chainsaws. This part helps turn the flying wheel when you pull on the starter rope. You may need a wrench set to replace this part. It is recommended to review your models diagram to verify the parts compatibility. This part is made of durable plastic and sold individually.

The OEM Carburetor Assembly includes the carburetor and primer bulb. This assembly is used to mix the air/fuel mixture to the proper ratio for combustion, and attaches to the intake of the engine. Installation requires a screw driver, pliers and socket set, and is rated as "Easy" by customers. If broken due to wear/fatigue/damage, the eng...Read moreine will run rough, be hard to start and have performance issues. If this happens, the part should be replaced. Refer to your make, model and diagrams to ensure this part is correct.

This is a standard hardware which has multiple applications based on your tool. It is sourced from original equipment manufacturer for use with a variety of power equipment. Please refer to diagrams for proper application. This screw is made out of metal and it is sold individually. Requires a hex key or an allen wrench to install or remove it.

This is a genuine Weed Eater part for use with Edgers and Trimmers. The recoil starter pulley spins the flywheel to start the engine. The most common reason for replacing the starter pulley is when the edger won't start. This part includes the pulley ratchet pawls, washer, and the screw. Here is a list of tools that are needed to install ...Read morethe recoil starter pulley a T25 Torx bit screwdriver, 11/16 inch socket, spark plug wrench, small flat head screwdriver, cord, Phillips head screwdriver, large flat head screwdriver and needle-nose pliers.