EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

PDW9700J10II General Electric Dishwasher - Instructions

All Instructions for the PDW9700J10II
121 - 135 of 427

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Basket Wheels Were Falling Off
1 person found this instruction helpful.
  • John from Magnolia, TX
  • Really Easy
  • Less than 15 mins
  • Pliers
This was a simple part swap. The stud rollers are the small peg-clips that hold the wheel on the lower dish rack. Removing the old stud rollers from the wheels required a pair of pliers. I then popped the new stud rollers into the old wheels and snapped them back onto the lower dish rack. I scored some major points from my frustrated wife -- easy, fast fix!
Was this helpful?
Thank you for voting!
Bottom dish basket would not roll in and out. Wheels were falling off.
1 person found this instruction helpful.
  • Randy from Placentia, CA
  • Really Easy
  • Less than 15 mins
  • Pliers
Removed the existing stud rollers with the wheels attached. Then removed the wheels from the stud roller. Then snapped the wheels on the new "Better Designed" stud rollers. Then easily snapped the new stud roller assembly in place. Piece of cake...works like a charm.

Thanks,

Randy
Was this helpful?
Thank you for voting!
wheels kept falling off bottom rack
1 person found this instruction helpful.
  • John from Easley, SC
  • Really Easy
  • Less than 15 mins
  • Pliers
Man, if you need help doing this repair, you shouldn't even own a dishwasher, much less a house. This was the easiest repair in the entire galaxy. First, I removed the old wheels, which was easy becasue they were always falling off by themselves. I then had to use pliers to squeeze the old studs to remove them from the wheels. All the wheels were still in good shape. Then I snapped the wheels onto the new studs, and snapped the studs onto the lower rack. And then, it was like I was in heaven. Bluebirds were singing, the sun was shining, my lower rack was sliding in and out and in and out like it was new. O happy day.
Was this helpful?
Thank you for voting!
Replace the middle flatware basket
1 person found this instruction helpful.
  • Marc from Brambleton, VA
  • Really Easy
  • 30 - 60 mins
So easy, even I was able to do it. Slide tabs back on defective basket and remove both sides, then slide the tabs onto new basket and place in dishwasher. All Done!
Was this helpful?
Thank you for voting!
Leaking valve
1 person found this instruction helpful.
  • Gary from HAVERHILL, MA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Used teflon tape around new 3/8 elbow. Re-installed valve in originals postion. Connected supply hose and reconnected electrical to valve.
Was this helpful?
Thank you for voting!
Plastic coupling broke on door cable counter balance
1 person found this instruction helpful.
  • Todd from DALLAS, TX
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Removed dishwasher from under counter. Removed both cable pulleys and bushings. Threaded new cables and remounted pulleys and bushings. Finally stretched springs onto cables. Checked counter balance and reinstalled dishwasher.
Was this helpful?
Thank you for voting!
Dishwasher was noisy during drying cycle.
1 person found this instruction helpful.
  • Carl from SUMMERFIELD, FL
  • Easy
  • 30 - 60 mins
  • Screw drivers
The noise came from the dishwasher door. Removed the Phillips screws from the door edge to gain access by separating the front of the door. Had to disconnect some of the electrical connectors to allow more access. Disconnected the blower motor connector. Removed the screws holding the motor assembly and removed the blower motor. Inst alled the new blower motor and reconnected the electrical connectors. Reassembled the door and cycled the dishwasher. Very quiet now!
Was this helpful?
Thank you for voting!
wouldn't drain
3 of 7 people found this instruction helpful.
  • JOHN D. from GOSHEN, IN
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Removed the dishwasher to get at the defective parts and removed,than replaced the two check valves and reassemble.
Was this helpful?
Thank you for voting!
Detergent dispenser did not work
1 person found this instruction helpful.
  • ARTHUR from OAK PARK, IL
  • Very Difficult
  • More than 2 hours
  • Pliers, Screw drivers
Followed the instruction video on your website. It was accurate and valid. The repair should have taken 15 mins., instead one of the screws holding the dispenser was frozen. Tried DW-40, and liquid wrench. Neither worked because the screw was in plastic.Finally got out the Dremel and cutting wheels. Had to cut away enough of the unit unt il I could get at the screw (it was the center bottom one). Sliced through some more of the housing, then cut a notch in the screw head deep enough so I could apply enough pressure with a flat blade screwdriver to open it. After that things went as smoothly as could be expected.A bad design and cheap materials.
Was this helpful?
Thank you for voting!
Mainly leaking Rince Aid, but occasionally the soap door did not open to dispense soap
1 person found this instruction helpful.
  • Edward from AVON, IN
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Watched the video, and followed the directions. Although my machine had some slight differences, the repair went pretty much per the video. Got all connections back where they belonged, cleaned up the insides a little while had the door parts separated, then buttoned it all back up, ran a cleaning solution thru empty washer, let it dry then started filling with dishes and ran the wash cycle the next day when full. All is well.
Was this helpful?
Thank you for voting!
Would only drain intermittenly
1 person found this instruction helpful.
  • C. from Lexington, KY
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Thought it might be check flapper valve on drain pump, so I replaced fairly easily, per instructions. When doing, I noticed the attached relay wires were not secure. When it was on the drain cycle one of the relay wires vibrated badly and loosened the connection enough to only work occasionaly. Would like to put new relay on the pump bu t they do not sell separately from the pump. (one assembly). I resecured connection and will wait till relay gives out and buy new assembly, but for now it's working perfectly!
Was this helpful?
Thank you for voting!
valve leaked
1 person found this instruction helpful.
  • Paul from KENT, WA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Wrench set
shut off water. removed lower panel disconnected power removed supply hose and outlet hose. disconnected electrical plug from valve. Un bolted valve from frame. removed elbow from valve inlet. installed elbow on new valve using Teflon tape. reinstalled valve to frame. connect hoses + electric plug to new valve. turn water on che ck for leaks. reconnect power. run dish washer check for leaks & popper operation. reinstall lower panel.
Was this helpful?
Thank you for voting!
No video for this new version of the part
1 person found this instruction helpful.
  • Ellen from DOVER, DE
  • Easy
  • 15 - 30 mins
The entire flat side of the end cap, (with the cutout latch), goes on the outside of the guide bar. It took less than 15 seconds to insert. It took about 30 minutes of searching for videos and playing around with the part to figure this out. A simple diagram would have been helpful.
Was this helpful?
Thank you for voting!
New install missing drain tube and clamp.
2 of 4 people found this instruction helpful.
  • David from Norwell, MA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers, Wrench (Adjustable)
Purchased new $1400 dishwasher from sales floor for $699. Cosmetically perfect, but missing drain tube and clamp. Seemed like a good deal... and it was. Needed parts were $34. Install of this machine was a breeze, and it is suoer quiet...I need to get down on the floor and listen for water flow to know that it's working. Really.
Was this helpful?
Thank you for voting!
Old soap dispensor latch would not hold
2 of 4 people found this instruction helpful.
  • Kenneth from Dublin, OH
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Turned off the power at the main box. Removed the six phillips screws and two bottom hex screws holding the front panel. Removed the two solenoid wires on the old dispenser (Label wire polarity). Removed the eight screws holding the old soap dispensor and took it out. Cleaned the area around the hole. Laid down a bead of silicon caul k around the hole edges. Placed the new dispenser in the hole and replaced the eight screws (do not over tighten). Replaced the two wires on the dispenser solenoid (check polarity). Replaced the front cover (Do not over tighten. Turned on the power and job complete.
Was this helpful?
Thank you for voting!
All Instructions for the PDW9700J10II
121 - 135 of 427