PCGS920SEF3SS General Electric Range - Instructions

It all began one find night baking and suddenly the oven would not light up. And so for the next few years all I ever used the stove for was for stove top cooking, See Im a single guy so its not in my nature to get to fancy when it comes to cooking home meals,but after a while the mood changes and you finally get up the motivation to fix ... Read more whats wrong. The change over went easy,easier than I expected.And the part worked just fine. As far as ease of the order and receipt,couldnt have been better,I got the part within 48hrs and that is fast! Thanks to all.
T.Melillo

the flame spreader through the years, developed a hole above the glow coil causing the above trapped gas between the oven pan and spreader to ignite. by replacing the flame spreader the problem is gone and is now working properly. thank you, parts select for being there when i needed the part and also being reasonably priced. mike marino

Take out inside of oven.Igniter is held on with 2screws and electrical clip.take off old one and put on new one.

Disconnect power. Remove oven door, oven racks, bottom pan, drawer below the oven. unsnap igniter wire connector. Remove two screws holding the igniter in place, remove igniter.

Install igniter (placing igniter wires away from any heat producing parts) and all parts in reverse order as they were removed.

Oven heats g ... Read more ood now, makes great cornbread and biscuits, the wife helps the oven do this.

determined that the top of the burner was melted and malformed. Repair was simple: lifted off the damaged burner and slipped the new one in place.

Was able to see the exact part with easy to read schematic so I knew I was ordering the right part. Then just switched out the old for the new. Looks like a new cooktop except for the scratches in the stainless, but we are working on that! Thanks!

Pretty easy in all. The connector from the igniter to teh power sorce didn't quite fit. Ijust cut off the new one and spliced the old one back on. Probably could have made my life easier if I took off the oven door, but it just meant I had to reach more. Works great, and other the connector, which I didn't really think would fit a 15 yea ... Read more r old oven,it was very easy/.

This would've been an easy repair, but I ran into some complications.

First I removed the thumb screws holding the bottom oven pan, took the pan out, and also took the bottom panel off the front of the oven.

This gives you access to the burner assembly. I disconnected the wire to the ignitor. I then removed one s ... Read more crew at the front, and two in the back of the burner assembly with a 1/4 socket wrench.

The burner assembly came out. I tested the ignitor for continutiy with a multimeter to ensure this was the faulty part. There was not continuity, so I knew the ignitor needed to be replaced.

This was when I tried to unscrew the ignitor, and both screws stripped their threads on the burner mounting plate. Complication #1. Seems with age, that mounting plate tightened up on the screws.

I cut the screw heads off with a dremel and cutting wheel to get them out. I'm glad I did this before ordering the new part because I needed to order the replacement screws too.

The burner mounting plate for the ignitor needed to be re-tapped to get the new screws in with a 10-32 tap and power drill.

Once the mounting plate was properly rethreaded, I attached the new ignitor, and reattached the burner assembly to the oven.

When trying to connect the wires, the plastic connectors wouldn't click together. They matched up fine, but wouldn't go all the way in. Complication #2. While the plastic connectors were properly mated, the inside pins were both female. The old ignitor had male pins on it, the new one had female pins. So I removed the burner assembly again, cut off the new ignitor connector and spliced in the old ignitor connector with the included porcelain wire nuts.

I put the oven back together again, fired it up, and it worked great.

Set the burner in place

Removed bottom shelf from inside oven, turned it obj and replaced the oven deflector with only a screwdriver

I removed the door and the racks, and the flame spreader. I removed the 4"X6" shield loosen the circular flap to plug the new igniter to the recepticle. Turn the oven on to check the operation and if it comes on, button it back up. remember open the oven door approx 3" and pull upwords to remove the door. I would say 90% of the time the i ... Read more gniter is the problem.

Just put it on. Quite proud of myself for figuring out what and how to get the part however! The website was very helpful.

Took longer to open the box.

Once we knew which part was needed, we went on to your site and orded the part. It was delivered the next day! Partselect.com is bookmarked on every computer in our household, including mobiles. It's great to know there is such a fantastic resource for do-it-youselfers. It took 5 minutes to remove the old igniter and plug in the new. A ... Read more screwdriver is the only tool required.

1. Unplug from electrical outlet. 2. Turn off gas valve. 3. Remove oven door. 4. Remove bottom drawer. 5. Remove oven shelves. 6. Remove oven floor, take out the two screws at the rear. 7. Unplug the igniter from the wire harness, you can reach it from where you removed the drawer. 8. Remove the igniter, by unscrewing the two bolts using ... Read more your nut driver. 9. Replace with new igniter. 10. Put everything back together, starting with # 9 and work your way to #1.