Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
oven post mini explosion sounding
14 of 23 peoplefound this instruction helpful.
Mchael J. from Chesterfield, VA
Easy
15 - 30 mins
Nutdriver
the flame spreader through the years, developed a hole above the glow coil causing the above trapped gas between the oven pan and spreader to ignite. by replacing the flame spreader the problem is gone and is now working properly. thank you, parts select for being there when i needed the part and also being reasonably priced. mike marino
Was this helpful?
Thank you for voting!
Gas oven was not lighting (bake only)
9 of 9 peoplefound this instruction helpful.
Jerry from MACOMB, MI
Really Easy
15 - 30 mins
Socket set
Repair was very easy. 2 screws to remove the bottom cover inside the oven. 2 more screws to remove the igniter. Cut the wires to remove it from the back of the oven. 3 screws to remove the back cover. Un-clipped old igniter , pushed new one through the hole (from inside the oven). Connected and re-applied screws. Worked like a charm.
Original burner cap was chipping; must have been dropped somewhere along the line.
8 of 15 peoplefound this instruction helpful.
Mitzi from Briarcliff Manor, NY
Really Easy
Less than 15 mins
New burner cap replaced old; just placed over burner; no tools required.
One suggestion: burner cap should have been shipped with thicker bubble protection (easy to do). It was minimally wrapped and placed in a thin, bubble envelope, risking damage in shipping process. Luckily, the burner arrived in tact and usable.
Was this helpful?
Thank you for voting!
Hole burned through deflector oven and metal dropped onto igniter and burned it out
5 of 6 peoplefound this instruction helpful.
Scott from ARDMORE, PA
Very Easy
15 - 30 mins
Screw drivers
Removed bottom shelf from inside oven, turned it obj and replaced the oven deflector with only a screwdriver
Was this helpful?
Thank you for voting!
One burner would not light from spark. All other burners lite with spark.
4 of 6 peoplefound this instruction helpful.
Thomas from DEARBORN, MI
Easy
30 - 60 mins
Nutdriver
First I checked that the wire and sparker was working by switching the wires on top of the range. I did this by pulling out the sparker switching it from the back working burner on the same side. The same burner would not light so I knew it was not the sparker.
Then watch a bunch of videos and found this gal to be the most he
... Read morelpful on how to take apart my exact stove. Go here: https://www.youtube.com/watch?v=WRGfuhUzEaY
I did not take everything apart like she did. I ordered the spark module and just replaced it following her method to take off the back, switch the wires to the new module, then put everything back together again.
All burners have been working perfectly since the fix.
Read less
Was this helpful?
Thank you for voting!
Large burner cap finish was damaged
3 of 4 peoplefound this instruction helpful.
Richard B from CLARKSBORO, NJ
Very Easy
Less than 15 mins
Just lifted old burner off with my fingers and replaced with the new one. What needs to be focused on here is the fact that Part Select has such a complete line of parts rather than the difficulty in the install.
Was this helpful?
Thank you for voting!
Original Grates and Reversible needed replacing. The replacements were a perfect fit.
3 of 5 peoplefound this instruction helpful.
Karen from CEDAR RAPIDS, IA
Really Easy
Less than 15 mins
Did a search and found PartsSelect. Inserted the model number of the GE Profile Gas Range. Located the the needed parts, and added to the 'shopping' cart. Then purchased, then waited for delivery.
My Orders
