Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
One burner would not light from spark. All other burners lite with spark.
4 of 6 peoplefound this instruction helpful.
Thomas from DEARBORN, MI
Easy
30 - 60 mins
Nutdriver
First I checked that the wire and sparker was working by switching the wires on top of the range. I did this by pulling out the sparker switching it from the back working burner on the same side. The same burner would not light so I knew it was not the sparker.
Then watch a bunch of videos and found this gal to be the most he
... Read morelpful on how to take apart my exact stove. Go here: https://www.youtube.com/watch?v=WRGfuhUzEaY
I did not take everything apart like she did. I ordered the spark module and just replaced it following her method to take off the back, switch the wires to the new module, then put everything back together again.
All burners have been working perfectly since the fix.
Read less
Was this helpful?
Thank you for voting!
Large burner cap finish was damaged
3 of 4 peoplefound this instruction helpful.
Richard B from CLARKSBORO, NJ
Very Easy
Less than 15 mins
Just lifted old burner off with my fingers and replaced with the new one. What needs to be focused on here is the fact that Part Select has such a complete line of parts rather than the difficulty in the install.
Was this helpful?
Thank you for voting!
Replaced temperature sensor
3 of 4 peoplefound this instruction helpful.
George from LANSDALE, PA
Difficult
30 - 60 mins
Screw drivers, Socket set
un-screw temperature sensor, have to move racks and door, then open back cover board to disconnect the sensor.
Was this helpful?
Thank you for voting!
Gas burner wasn’t burning properly
2 of 2 peoplefound this instruction helpful.
Karin from ARUNDEL, ME
Really Easy
Less than 15 mins
I ordered the new burner head and replaced it and now it works perfectly.
Was this helpful?
Thank you for voting!
burner had hot spots where the matieral melted some cause a distorted flame that would spit sputter
2 of 2 peoplefound this instruction helpful.
Dan from WARROAD, MN
Really Easy
Less than 15 mins
Nutdriver
Remove the top grate and remove the top burner plate and then pull the burner out and remove the torx screw and adapter install onto the new burner and place back on the stove , good to go.
Was this helpful?
Thank you for voting!
Burner had uneven flames
3 of 5 peoplefound this instruction helpful.
Akshay from Bridgeton, NJ
Really Easy
Less than 15 mins
Too easy a five year old could do it
Was this helpful?
Thank you for voting!
The eye would not light
2 of 2 peoplefound this instruction helpful.
Solomon A from COLLEGE PARK, GA
Really Easy
30 - 60 mins
Remove the existing burner and install the replacement.
Was this helpful?
Thank you for voting!
Center knob for hot griddle did not turn
2 of 2 peoplefound this instruction helpful.
Imogene from SANTA MARIA, CA
Easy
30 - 60 mins
Screw drivers, Socket set, Wrench set
We bought a new valve burner from your company and put it in ourselves. It works great. Thank you so much. We spent a little over $30.00 instead of calling a repairman (which we couldn't afford).
Was this helpful?
Thank you for voting!
Food ran over the burner and damaged it.It was easy to place it back inII
1 personfound this instruction helpful.
Alan from PASADENA, TX
Really Easy
30 - 60 mins
It only required placing the new burner in the proper location.
Was this helpful?
Thank you for voting!
some of electrodes not working at times,found were bad,wires had some insulation missing, clips looked burnt,found all new parts replaced
1 personfound this instruction helpful.
Dana from LEEDS, AL
Really Easy
More than 2 hours
Pliers
the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.
Was this helpful?
Thank you for voting!
flame was inconsistent. too much air.
1 personfound this instruction helpful.
Raymond J. from EASTPORT, NY
Really Easy
Less than 15 mins
replaced old with new.
Was this helpful?
Thank you for voting!
The old burners were damaged by the prior owners.
1 personfound this instruction helpful.
Mohammad from BARTLETT, IL
Very Easy
Less than 15 mins
The repair was extremely easy. Just removed the old burners and dropped in the new ones. No tools needed.
Had two burners on the stove that would not light. Had tried cleaning them but they still did not ignite. Replaced both burner heads. Once replaced. they ignited right away and have worked ever since.
I got really great customer service on finally getting the right part. It came really fast it fit perfect but the cap is a high gloss black instead of a flat black. I will need to call customer service again to see if they can the correct color this time. Otherwise everything was great!
Was this helpful?
Thank you for voting!
BASE OF BULB BROKE OFF & WELDED TO SOCKET
1 personfound this instruction helpful.
NEIL from ROCKY POINT, NY
Easy
30 - 60 mins
Nutdriver, Pliers
PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.
My Orders
