- Home
- PB970SP2SS
- Instructions
PB970SP2SS General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
oven not as hot as temp display said it was
4 of 4 people
found this instruction helpful.
-
John from HOT SPRINGS, AR
- Really Easy
- 30 - 60 mins
-
Nutdriver
pull out stove, unbolt old temp sensor inside stove with 1/4 nutdriver, go to back of stove and take off cover and unhook sensor and hook up new one, put all back together and slide stove back in place.
Was this helpful?
Thank you for voting!
F2 Error on Display
4 of 4 people
found this instruction helpful.
-
Tom from FORNEY, TX
- Very Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
The repair was very easy to do. Our oven was showing the F2 error code, which is associated with an over-temperature fault. Upon inspection, the oven was warm, but definitely not beyond the temperature threshold. I researched the issue and found this temperature sensor.
Swapping the sensor was extremely easy. You take off the back pa ... Read more nel of the oven, unhook a single wiring harness, and undo some bolts inside the oven, which allows you to pull off the old sensor. Simply hook up the new sensor to the harness, pull everything back through, replace the fasteners, and you're good to go.
Swapping the sensor was extremely easy. You take off the back pa ... Read more nel of the oven, unhook a single wiring harness, and undo some bolts inside the oven, which allows you to pull off the old sensor. Simply hook up the new sensor to the harness, pull everything back through, replace the fasteners, and you're good to go.
Read less
Was this helpful?
Thank you for voting!
Oven Temp. went too high and the door locked. Burnt the food
4 of 4 people
found this instruction helpful.
-
Nathan from BILLINGS, MT
- Very Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
This temperature sensor is very easy to replace. There are two screws inside the oven in the top middle of the back of the oven. Take these off. on the back of the stove there is a metal plate with 5 screws I believe. Take these off with a nut driver. Then you will see a white connector coming from the spot where you took the other screws
... Read more
off. Take the white connector apart and pull out the temperature sensor from the inside of the oven. Then put the new one in.
Read less
Was this helpful?
Thank you for voting!
Element bad
4 of 4 people
found this instruction helpful.
-
Cheryl from JOHNSONVILLE, SC
- Very Easy
- Less than 15 mins
-
Socket set
Since this was the third time I did it all I had to take two screws out to lift the top of stove and replace element.
Was this helpful?
Thank you for voting!
Oven slow to heat.
6 of 10 people
found this instruction helpful.
-
Scott from Burleson, TX
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers, Screw drivers
First I removed the 4 screws that hold the element in place. I then pulled the element out about 3 inches. I removed the sensor and disconnected the connector.
Was this helpful?
Thank you for voting!
Broker inner glass
4 of 5 people
found this instruction helpful.
-
marc from PARK RIDGE, NJ
- Really Easy
- 15 - 30 mins
-
Screw drivers
Very easy to remove the parts and to reassemble
Was this helpful?
Thank you for voting!
Incorrect oven temperature due to defective temperature sensor.
3 of 3 people
found this instruction helpful.
-
Anthony from FARMINGVILLE, NY
- Really Easy
- Less than 15 mins
-
Nutdriver
Performed repair using a video for reference.
Was this helpful?
Thank you for voting!
Needed to replace 12 in heating element
3 of 3 people
found this instruction helpful.
-
Steve from ELMONT, NY
- Very Easy
- Less than 15 mins
-
Screw drivers, Socket set
Took a picture of the old heating element to make sure that when I replaced the new element the wires were in the exact location as before.
Was this helpful?
Thank you for voting!
F2 Warning - Oven overheating
3 of 3 people
found this instruction helpful.
-
john from bend, OR
- Really Easy
- Less than 15 mins
-
Socket set
I checked various sites on the net and decided that the temperature sensor was the problem. The GE price for the replacement part was about $105, most of the other sites offered the sensor in the $70 range. PartSelect $12.95 When the part arrived, I removed a small self taping screw, pulled the high temperature wire connector into th
... Read more
e oven space, disconnected the quick disconnect fitting, attached the new temperature sensor, pushed the connecting wire into its hole, replaced the screw and that was it. I probably saved about $200 in parts and labor over what a local repairman would have charged. Oh yes!! I first disconnected the power at the breaker box. Very important.
Read less
Was this helpful?
Thank you for voting!
Inner glass assembly had cracked
3 of 3 people
found this instruction helpful.
-
Richard from Gorham, ME
- Really Easy
- 30 - 60 mins
-
Socket set, Wrench set
Took the oven door off and removed the inner door panel, put new glass assembly part in and reassembled. The hard part was getting the door hinges locked back into place.
Was this helpful?
Thank you for voting!
Original heating Element was burned out
3 of 3 people
found this instruction helpful.
-
Janice from ST CLR SHORES, MI
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
1st replacement part was damaged from Shipping.
Parts Select sent a new one that i received in only a few days.
our stove is slid into a granite island so the disassembly was not as simple as most. It was necessary to remove the controls, the controls housing & screws along the top of the oven door.
Within an hour the sto ... Read more ve was back in place and working perfectly.
Great service from Parts Select
Parts Select sent a new one that i received in only a few days.
our stove is slid into a granite island so the disassembly was not as simple as most. It was necessary to remove the controls, the controls housing & screws along the top of the oven door.
Within an hour the sto ... Read more ve was back in place and working perfectly.
Great service from Parts Select
Read less
Was this helpful?
Thank you for voting!
Returned Part to your location per Returns, Reference 15681540.
3 of 4 people
found this instruction helpful.
-
William from FREDERICKSBRG, VA
- Very Difficult
- 30 - 60 mins
Part WB30T10126 Triple Haliant Element-12 Inch was returned to you under Returns Reference 15682540. Mailed by USPS Tracking #9505 8161 4647 1005 7628 41. According to USPS, it arrived at your location Friday, Jan. 15, 2021 @ 10:49 AM. Please advise. Thank you, William Deal
Was this helpful?
Thank you for voting!
The temperature indicator light on the oven was broken.
3 of 4 people
found this instruction helpful.
-
Jewel from Nacogdoches, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
I removed the control panel by removing 7 screws and replaced the light indicator and lens.
Was this helpful?
Thank you for voting!
Oven Light Assembly damaged
5 of 10 people
found this instruction helpful.
-
Jose from Frederick, MD
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
I have a double oven and coincidently I had to replace the two Oven Light Assemblies.
I am really glad about your web site because once I got the number from my oven model you guys were the first ones that came up. Thanks to your prompt and reliable service my oven is back to its original state.
Jose Figueroa
I am really glad about your web site because once I got the number from my oven model you guys were the first ones that came up. Thanks to your prompt and reliable service my oven is back to its original state.
Jose Figueroa
Was this helpful?
Thank you for voting!
One of the heating elements wasn’t working.
2 of 2 people
found this instruction helpful.
-
Adam from WEST JORDAN, UT
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I just watched the video that was on the website. It showed in detail how to replace the heating element. After watching it I was able to remove the cooktop, replace the heating element and put it all back together. The only issue I had was getting the cooktop loose but once I did everything else was easy.
Was this helpful?
Thank you for voting!