PB911SJASS General Electric Range - Instructions

Disconnect power, then remove racks from oven, locate heat sensor by the broiler element. Use ratchet with extension and correct socket to remove the bolt directly under the heat sensor, pull the sensor out till you see the plug, disconnect the plug and then connect new sensor to it push wire back thru and then rebolt the new sensor on, ... Read more thats it...

Tried GE onoine parts department first and ordered the wrong part, then tried the customer hotline and they referred me to the right part but didn't explain that the design had been modified (the drawings had not been updated). I found an explanation on Part Select AND the parts were cheaper. Part Select sent the part, the necessary scr ... Read more ew, and an appropriate instruction manual. Each support took less than a minute to screw in with a socket wrench.

Unplug stove.2 screws out ,lift top ,disconnect bad element, connect new element, put top down .2 screws in .plug stove back in...EASY PEASY

Ordered the part, turned off the circuit breaker, test to see that power is off, take a 5/16” nut driver, and remove the 2 screws under the front of the stove top, then lift the top up and hold it up with an old 2x4 about 24” long. All the connections are plug and play, so I took some needle nose pliers, to pull all 5 wires off of the bur ... Read more ner. Then all that’s left to do is remove 3 spring clips. That was easily done by inserting a flat screwdriver into the back of each clip and pry them out. It ended up being a very easy fix. There is Utube videos to show you how to do it.

I changed out the sensor and still same problem. Change out Thermosat and still same problem.
I call the help number and emailed the help but I got nothing but have to many calls because of the virus situation.
Still need help.
I’m an electrician and I don’t want to call a service technician and pay that big bill.
... Read more Can anyone there help me out, if so please call.
Ike Stanton
678-525-6644

This should have been a very easy fix. But, as I tried to pull out the old temperature sensor, the wire would not come out. I was afraid to pull too hard because I did not want to break the wire. So, I coxed it out easily until I could see the plastic connector. Then, the old wire pulled free from the connector leaving the end of the c ... Read more onnector inside the back of the oven. I then had to fish the end of the wire around with the piece of wire through the very small hole in the back of the oven. Once I got it close to the hole, I was able to grab the connector with some needle nose plyers. Connecting the new sensor and reinstalling everything was easy and the oven now works just fine.

Pulled the oven out and unplugged it. Removed five screws and the back cover. Disconnected the electrical connection. Removed one screw and pulled the sensor out. Installed the sensor and screw. Made the electrical connection on the back, replaced the cover and five screws. Plugged the electrical cord back in and tested the oven tem ... Read more perature compared to the setting. Worked great. My wife then made a small batch of muffins to test it out and they were good.

I just followed the instructions on the link provided with the part

Disconnect old burner and reconnect new one

Initially replaced the switch on the range--a simple job--pull the wires one by one and place them on the new switch. This did not resolve the problem, which meant that it was the burner, not the switch. I left the new switch in place and ordered a new burner. This, too, was simple, but involved creating a detailed drawing of the switch c ... Read more onnectors rather than photos, which, because of the crossing of similarly colored wires, might have been confusing. The only hitch was that the burner is attached to the top by indented clips that fit into pegs at numbered locations on the burner. The clips were very difficult to open and situate, but once done (and this step was the only one where a second person was required) the top was closed and screwed back in place (two screws) and it worked perfectly.

Well I did it all wrong from the get go. I did finally do a search on how to replace it and then it was quite easy. Learn from me, watch video and save yourself tons of hassle.

Not counting unplugging it and taking off the 3 back panels of the oven (< 5 min.) It took < 2min. to change out. Unclipped cable in back, unscrewed one screw inside of oven at top between the two elements and pulled cable through to front, reversed to attach new sensor. Buttoned up the back, plugged back in and was good to go.

Open the oven , remove one screw holding the sensor remove the sensor and replace the sensor.

Watched repair videos on YouTube to prepare. The repair was very easy.

Being a front burner, I used a 24 in piece of wood to hold up range top. After removing to screws holding top. Made note of numbers on old burner and wire locations. Took off wires and three spring clips. Then replaced with new in numbered locations , wires next