PB900TP2WW General Electric Range - Instructions

After reading about possible losses of the wire leads, I put together a simple solution. First, turned off the breaker, then pulled the grates out for full access.
Using a nutdriver on the hex-head screws holding the backing plate to the oven wall, I removed the screws, then gently lifted and pulled the element and it's attached wire ... Read more leads out of the insulated rear of the oven.
Attach a plastic clothespin to each lead above the spring clip attaching the lead to the element so the springy wire would not tend to pull back into the difficult-to-access insulated area "behind the wall" because that would be a real pain to get at.
With nothing other than fingers, the spring clips can then be removed from the tabs on the element, the old piece removed, the new element set in place and quickly re-connected. No Problem!

Pulled stove out to access back panel. Unscrew broken switch/stem. Replaced each wire one at a time to make sure they went in right spot. Screw in new switch. Replaced back panel.

So easy. Took extra time so the wife would think it was harder. Just read the other reviews for instructions. Didn't have an issue with the wires pulling back into the oven though I did have my "clips" ready.

popped the new one on!

Pulled out stove. Removed rear panel, and set aside. Removed melted bake element by unscrewing the mounting plate screws, and unplugging both leads from the stove. Replaced in reverese fashion. Easiest electrical replacement I have done.

We decided to go "on line" to see if there was any way to fix the stove ourselves and found the Part Select website. After entering the model number for the stove, we were able to find the heating element. We ordered it and received it two days later! We saved money and time. Thank you!

Followed example on YouTube! Very easy.

I googled and did the step by step removal and installation of the element from a web site.. EHow

Repair was fairly easy. Had the problem that I had read about with one of the connection wires falling behind oven. Time consuming to take of back of stove but otherwise all went very well.

First I pulled stove out away from wall and unplugged the power cord then I removed the oven door to make repair much easier. I removed the two screws holding the heating element in place. I then went behind stove and unscrewed four screws to remove panel covering the electrical connections. Disconnected wires to heating element. Removed ... Read more old element and reversed each step to connect new element.

When the new element arrived I turned off the power to the stove, opened the oven, removed the 2 racks inside and took the 2 screws out of the old element. I slowly pulled it toward the oven door to expose the wires attached to it and was able to slip one wire off the old element and hold it with vice grips so it wouldn't slip back into t ... Read more he stove. Unfortunately the other wire slipped off the element on it's own and immediately went back inside the stove. Our stove is a slide in so, after trying to fish out the wire for about 5 minutes with an ice pick, I gave up and slid the stove out, turned it sideways and removed the 7 screws holding the vertical center cover on the stove back. When I removed the cover the wiring was exposed so I re-routed the lost wire to give me some slack and then pushed it back through the hole into the oven. I then opened the oven door, slipped both wires onto the new element, reattached the element to the oven wall with the 2 screws and turned the power on and checked the new element. I then closed the oven, reattached the back plate and slid the stove back into place. Oh, and while it was out I took the opportunity to clean the area where it sits. All in all it was a simple job, just a little time consuming.

The repair was easy to fix. I unplugged the stove to be safe, unscrewed the broken element and disconnect. And reconnected the new element and screwed it into place.

turned off power to stove.
removed old coil, as instructed by internet info.
replace new coil.

il

This was my first attempt at an appliance repair. The job did nit look too difficult so I thought I would give it a try. The most important thing I can recommend is to have some type of clips to hold the wires after disconnecting the old element. As soon as you disconnect the wire, it retracts into the insulation. My job became more diff ... Read more icult and required pulling out the stove, removing the rear panel, and now needing a second person to push the wires back Into the oven. What should have been a 15 minute job now was a 30 minute procedure. Keep in mind that when you pull a stove out you now have to get the cleaning supplies out also. Word to the wise:USE THOSE PLASTIC SNACK BAG CLIPS! To hold the end of the wires.

First- I slid the ove out and unscrewed the back metal piece/flap that covers where the element attaches to wires.
Second- I unscrewed the two nuts/screws that holld the element in place-An appropriately sized socket wrench would have made it way easier.
Third-Before pulling the element out, I disconnected the wire connection-th ... Read more e element tab just slid out of the connector.
Fourth- Pull out the old element and replace with new one. Attach wires before screwing in the element place holders.
Fifth-Replace back cover and screws. slide oven back into its nook,
Sixth-Bake some cookies.