PB900TP1WW General Electric Range - Instructions

Pulled stove out to access back panel. Unscrew broken switch/stem. Replaced each wire one at a time to make sure they went in right spot. Screw in new switch. Replaced back panel.

I unscrewed the 2 screws that held in the element, pulled it out a little, disconnected the 2 wires, got the new element out of the box, connected the two wires on the new element, put the screws back in and it was done! Very easy.

After reading about possible losses of the wire leads, I put together a simple solution. First, turned off the breaker, then pulled the grates out for full access.
Using a nutdriver on the hex-head screws holding the backing plate to the oven wall, I removed the screws, then gently lifted and pulled the element and it's attached wire ... Read more leads out of the insulated rear of the oven.
Attach a plastic clothespin to each lead above the spring clip attaching the lead to the element so the springy wire would not tend to pull back into the difficult-to-access insulated area "behind the wall" because that would be a real pain to get at.
With nothing other than fingers, the spring clips can then be removed from the tabs on the element, the old piece removed, the new element set in place and quickly re-connected. No Problem!

So easy. Took extra time so the wife would think it was harder. Just read the other reviews for instructions. Didn't have an issue with the wires pulling back into the oven though I did have my "clips" ready.

Pulled out stove. Removed rear panel, and set aside. Removed melted bake element by unscrewing the mounting plate screws, and unplugging both leads from the stove. Replaced in reverese fashion. Easiest electrical replacement I have done.

We decided to go "on line" to see if there was any way to fix the stove ourselves and found the Part Select website. After entering the model number for the stove, we were able to find the heating element. We ordered it and received it two days later! We saved money and time. Thank you!

Followed example on YouTube! Very easy.

I googled and did the step by step removal and installation of the element from a web site.. EHow

First I pulled stove out away from wall and unplugged the power cord then I removed the oven door to make repair much easier. I removed the two screws holding the heating element in place. I then went behind stove and unscrewed four screws to remove panel covering the electrical connections. Disconnected wires to heating element. Removed ... Read more old element and reversed each step to connect new element.

The repair was easy to fix. I unplugged the stove to be safe, unscrewed the broken element and disconnect. And reconnected the new element and screwed it into place.

turned off power to stove.
removed old coil, as instructed by internet info.
replace new coil.

il

My 8 year old son did the repair while I explaned what to do,that was the best part of this stove problem. My burner caught fire when it broke and really scared my children. I looked up the part on Part-Select and ordered it. To my complete surprise it arrived the next day(I did not pay for overnight) My son wanted to learn how to take ... Read more out the old one and put in the new one so I let him. Thanks for a GREAT learning time with my son and for your super service!! Ed

Used Socket set to remove the two screws in the oven to unplug and replace, had to also take the back pannel off the stove to get the new unit connected into the socket, total time less than 30 min.

Unplugged the stove.

Needed 1/4 inch socket to remove screws holding element and the back panel.

Removed the electrical connections on the element and then removed the old element and replaced with the new element.

Replaced screws holding the element in the oven.

Replace the electrical connect ... Read more ions on the element in the back of the stove.

Replaced the back panel.

Plugged the stove in and tested out.

First- I slid the ove out and unscrewed the back metal piece/flap that covers where the element attaches to wires.
Second- I unscrewed the two nuts/screws that holld the element in place-An appropriately sized socket wrench would have made it way easier.
Third-Before pulling the element out, I disconnected the wire connection-th ... Read more e element tab just slid out of the connector.
Fourth- Pull out the old element and replace with new one. Attach wires before screwing in the element place holders.
Fifth-Replace back cover and screws. slide oven back into its nook,
Sixth-Bake some cookies.