PB900SP3SS General Electric Range - Instructions

Pulled stove out to access back panel. Unscrew broken switch/stem. Replaced each wire one at a time to make sure they went in right spot. Screw in new switch. Replaced back panel.

Pulled out stove. Removed rear panel, and set aside. Removed melted bake element by unscrewing the mounting plate screws, and unplugging both leads from the stove. Replaced in reverese fashion. Easiest electrical replacement I have done.

I unscrewed the 2 screws that held in the element, pulled it out a little, disconnected the 2 wires, got the new element out of the box, connected the two wires on the new element, put the screws back in and it was done! Very easy.

After reading about possible losses of the wire leads, I put together a simple solution. First, turned off the breaker, then pulled the grates out for full access.
Using a nutdriver on the hex-head screws holding the backing plate to the oven wall, I removed the screws, then gently lifted and pulled the element and it's attached wire ... Read more leads out of the insulated rear of the oven.
Attach a plastic clothespin to each lead above the spring clip attaching the lead to the element so the springy wire would not tend to pull back into the difficult-to-access insulated area "behind the wall" because that would be a real pain to get at.
With nothing other than fingers, the spring clips can then be removed from the tabs on the element, the old piece removed, the new element set in place and quickly re-connected. No Problem!

So easy. Took extra time so the wife would think it was harder. Just read the other reviews for instructions. Didn't have an issue with the wires pulling back into the oven though I did have my "clips" ready.

Followed example on YouTube! Very easy.

We decided to go "on line" to see if there was any way to fix the stove ourselves and found the Part Select website. After entering the model number for the stove, we were able to find the heating element. We ordered it and received it two days later! We saved money and time. Thank you!

Removed old baking element by removing two sheet metal screws inside the oven and pulling out the old element. When pulling out the old element, one of the wires was too short and popped back into the back of the oven. I then had to pull out the oven, take the shielding off the back of the appliance, gain some slack in the wire and push ... Read more it back into the interior of the oven. I connected the new element and was finished with the repair.

First I pulled stove out away from wall and unplugged the power cord then I removed the oven door to make repair much easier. I removed the two screws holding the heating element in place. I then went behind stove and unscrewed four screws to remove panel covering the electrical connections. Disconnected wires to heating element. Removed ... Read more old element and reversed each step to connect new element.

Took two screws out, unplugged the wires.

Put the new heating element in. Plugged in the wires and put the screws back.

Took about 16 minutes !

Turned off power to stove. Removed burned-out element by removing two sheet metal screws and disconnecting two push-on electrical terminals.

Installed new element by pushing on electrical terminals. Pushed the new element back in place and secured with two sheet-metal screws.

Turned power back on and tested element ... Read more . All OK.

pulled out old element by unscrewing the 2 bolts in the back and vcarefully pulled out the two wire s . wires are very tight so if you let go of them which i did you will need a pair of needle nose plires to pull them out. other than that the installation is easy

1. Turn breaker to off position.
2. Using socket wrench, remove the old element.Takes a little prying to remove the connection from the eletrical wires.Be careful.
3. Insert new part and tighten with socket wrench.

Used Socket set to remove the two screws in the oven to unplug and replace, had to also take the back pannel off the stove to get the new unit connected into the socket, total time less than 30 min.

Unplugged oven, turned off breaker, took cover off back of oven, removed old sensor by disconnecting in back of oven and undoing screw inside oven. Pulled old one out replaced with new took 15min. Cost me less than $20. Parts Select rocks! Even received part in two days with standard shipping!