PB750DP1BB General Electric Range - Instructions

Turned off circuit breaker to range.
Removed the 2 oven racks. Removed two screws in back of oven compartment. Pulled element forward and the terminal connections get exposed.
The right terminal clip disconnected by itself and the wire went back into the stove and could not be retrieved.
Removed range draw under the oven an ... Read more d pulled entire range out from wall about 4 feet.. Removed metal backing with a socket wrench and exposed the oven element wires and terminals.
Reinstalled new element and metal backing.
Since range was out from wall, cleaned and vacuumed before pushing stove back in place.
Since range draw was out re-leveled by setting adjustable feet.
Reinstalled drawer and racks.
Turned on circuit breaker.
Tested element by setting bake cycle on.

After the element cooled down, I pulled the racks out of the oven, turned off the oven at the breaker box, then, using a nut driver, loosened the screws that held the baking assembly in the back of the oven, and pulled the connecting wires off. I bent the wires to make sure they would stay out, because if they get back in the insulation, ... Read more they are hard to find. I would recommend getting a pair of locking pliers and putting them on the ends of the wires just to keep them from getting back into the insulation. Then I attached the left connection wire and then the right one, pushed them back into the insulation, tightened the baking assembly to the back wall of the oven, turned it back on at the breaker box, then tested the oven to see if it heated up. It did. Total repair time 15 -20 minutes. Would have been less if I didn't have to chase one of the wires back in the insulation. Shamless plug for the company ...By paying extra for 2-day shipping to receive the part, I saved just over $20 from buying it at Sears, which would have had to order the part anyway.

Removed six 1/4" hex nuts on rear of oven. Then through front/inside removed a single 1/4" hex nut to actually remove sensor. Unplug sensor connector, remove. Reversed steps, push oven back in place and plugged in. Tested oven function.

removed the oven racks. used a 6.5 mm socket to take out two bolts. pulled out old element and wires through insulation into oven. i used caution during this part i didn't want the wires to disconnect and fall into the oven. once the wires and element was pulled out approximately 3 inches. i used two magnet clips that hold papers ont ... Read more o the refrigerator and clipped both wires so they wouldn't go back into the stove. disconnected the element from the wires and connected the new element to the wires. pushed wires into the back of the oven and tightened the two 6.5 mm bolt. done in 10 minutes. turned oven on to 400 degrees and let same pre heat. a little smoke will come from the new element which is normal. works fine now.

My husband had turned the oven on to cook something and didn't know that I have a plastic tray in there. Well, needless to say I needed to get some new oven racks. I tried to get them through the manufacturer (GE). They were 68$ each. I thought that was a bit steep, so I looked online. I decided to order through PartsSelect. Well...they ... Read more can 2 days later (the week before Christmas!!)and were a PERFECT fit.
Between the price, shipping speed and quality I will
definitely buy from again and recommend this site to everyone I know!!!!

Oh yeah, I work for Sears too. we have access to all sorts of parts....this site is the BEST for prices and delivery speed!!!!

After I got the right part(I ordered the wrong one at first, my fault) it was simple to remove the old element, 2 screws and push on termilnals, and replace with perfectly fitting new part. Word of caution, turn off the breaker to stove. I found that the element line is hot even if the control is off!

The existing terminal block on my Ge oven/Range had melted due to a loose wire causing sparking and starting the plastic casing of the terminal block on fire and melting it, Part select made the part easy to find and had it at my house in 2 days. All I had to do was remove six screws to take the back sheet metal cover off of the oven. U ... Read more nscrew the terminal connections remove two mounting screws that held the terminal on to the oven body. This was a little trickier than it should have been because the melted plastic had reformed making it very hard to access the mounting screws. i then mounted the new piece and plugged the oven in, it took 15 minutes and was very easy. definitely saved me at-least a $100 for the service call i would have made if finding the part wasn't so convenient

I started by Unscrewing the range top. 2 small screws. I took off the old piece by unclipping the piece . Then I color coded each wire so that I would know exactly where I would place the wires for the new part. 30 min maximum time spent changing the part. Please don't forget to unplug the range before you start.

Unplugged appliance and removed 5 screws on back of stove/oven and removed plate. Disconnected the sensor and unscrewed it on the inside of the oven. Pulled the cord through and replaced with new sensor. Replaced all parts and plugged in the appliance and tested. Worked great.

The repair went very easy. The replacement part was designed differently than the original part. It installed on the rear of the drawer with a screw as the original snapped into the side. This was a bit confusing when researching and looking up the part online.

Slide range out. Remove screws holding back vent in place. Remove back vent. Remove screws under front panel and knobs. Lift glass cooktop. Remove screws holding switch in place (behind knob) unplug each wire from switch and immediately replace in same spots on new switch. Replace everything.

1) pull out the stove
2) remove the 7 sheet metal screws holding the back panel on. (the panel that also covers where the cord splits and connects to the oven.
3) Find the small plastic connector located in the middle of the back of the range and unplug it.
4) open the front of the oven and remove the one screw holding in ... Read more the oven temp sensor.
5) replace the sensor and make sure to "feed" the new cord through as best you can.
6) I had to dig through the insulation a little bit to find the new wiring harness
7) connect the wiring harness and put the back of the range back on

note: this was very simple to do if you think this might be the problem don't hesitate to handle this one yourself.

Took old racks out, slid new ones in....exact match at a huge savings from what GE wanted per rack.
Found the company through a Google search, have it bookmarked and will be back if I need something from them.

Unplugged unit. Removed racks from oven. Removed screws from bracket holding element in. Carefully pulled element forward until the wire connections were exposed. Removed wires taking care not to let them retract into the oven. Removed element from oven. Placed new element in oven. Connected wires to element. Replaced screws to hol ... Read more d element in. Replaced racks. Plugged in oven. Turned on to see if working.

First step is to unplug the range. Then simple to remove top portion of two part back panel behind controls console, then remove knob and two screws for control, then use needle nose to transfer push-on connectors from old control to new control one at a time, finish re-assembly in reverse order.