PB-24LN Echo Leaf Blower / Vacuum - Overview

This is a genuine ECHO/Shindaiwa replacement part It is compatible with over 150 machines listed below. The Fuel Line Grommet is placed into the fuel tank. The Vent tube, Fuel return line and fuel line are inserted through the three holes. A worn Fuel Line Grommet will cause fuel to leak from the tank. When replacing the Grommet it is advisable to replace the fuel lines at the the same time.

This OEM Fuel Filter is a silver and white, steel/felt, part measuring about 1.25 inches in length and 3/4 inch wide. It can be installed with pliers and is rated as Easy to install by customers. This part attaches inside the fuel tank to clean the fuel of debris, and should be replaced during regular maintenance, check your manual for ...Read morerecommended replacement time. If the filter is leaking or it has a blockage preventing fuel flow, then it should be replaced. If the engine sounds like it is not getting enough fuel, then remove the filter and check it for blockage.

The Primer Pump, aka the Pump Bulb, is a clear, individually sold, plastic part, sourced from the original equipment manufacturer. It has an Outer Diameter of 0.616 Inches, 15.66mm and is 0.558 Inches and 14.19mm in height. This part is used to pump fuel from the tank to the carburator and is rated Easy to install. This part installs on...Read moreto the primer assembly. If the part dries out or starts leaking that means it is broken (likely due to fatigue or general wear) and must be replaced. Check the model number to ensure you are choosing the right part.

This a a genuine OEM replacement check valve for your small engine. It is also known as a fuel tank vent. You may need to replace this part if you are noticing debris or dirty oil in the reservoir. Make sure the engine is cool before you begin this repair, and remove the wire and boot from the spark plug to prevent the engine from starting up.

Genuine Echo Replacement part, this item is sold individually. The 13031051830 Air Filter is used to keep dust and debris from contaminating the carburetor and engine. This filter is used on all the Echo Outdoor Products listed below. When this Filter gets clogged and dirty it will diminish the performance of the engine. It should be replaced at this time.

This part is the fuel return tube for your outdoor power equipment. It is made of yellow plastic and measures 3x6x110mm. The return tube transports excess fuel back into the fuel tank after the primer bulb has been pressed and has primed the carburetor so the engine can start. Over time, this fuel tube can crack or clog, and this can caus...Read moree problems for the engine. To replace this part, carefully pull the tube off the carburetor and the fuel tank, then connect the new tube. This part is sourced directly from the manufacturer and is an OEM part. It is sold individually.

This spark plug is sourced from the original equipment manufacturer. It is a small device in the engine cylinder head which is responsible for creating the spark that ignites the fuel in the engine and allows the engine to run. The spark plug comes in a cylindrical shape and is wrapped in a ceramic/porcelain insulator. It has a metal rod,...Read more known as the center electrode in the center and a metal tab at its base, known as the ground electrode. The spark plug may fail due to a buildup of carbon, physical damage, or fouling. To confirm that the spark plug is faulty, visually inspect it and use either a multimeter set to continuity or a spark tester to test the spark plug for electrical failure. Unthread the faulty spark plug using a spark plug socket and ratchet. Use a spark plug gap tool to set the correct gap and finally, carefully thread the new spark plug into the engine. Regularly inspect and replace your spark plug as part of your general maintenance to keep your equipment in good condition.

Also referred to as a Spark Arrester, this Spark Arrester Screen is an authentic OEM replacement part that is not part of a kit or assembly. It is made of metal and sold individually. The purpose of this screen is to prevent flammable debris from entering the engine and becomes worn through regular use. If the screen is clogged, remove th...Read moree screen from the muffler, hold it with pliers, and use a torch to burn off the debris before reinstalling the screen. This part needs to be replaced when it becomes damaged or worn. When the screen is malfunctioning, you may notice debris exiting through the muffler. To complete this repair, you will need a screwdriver and pliers. This screen is located within the muffler; refer to your owner's manual for the exact location on your model. Customers rated this repair as Easy.

This OEM nut is a 5mm, gold, metal nut, which is sold individually. It can be installed with a Wrench or Socket and Torque Wrench by torquing to the manufacturer specifications. This nut is used to secure another part in place, and should be replaced if damaged due to fatigue (such as damaged threads or rounded ends). This nut can have v...Read morearious uses on various equipment, and as such the difficulty of the installation can vary, but generally this is an easy repair.

This is a genuine OEM sourced replacement part designed for use with Echo blowers/trimmers. This is a standard hardware which has multiple applications based on your unit. Please refer to diagrams for proper application. This screw is made out of metal and it is sold individually. To remove or install this screw you would need a screwdriver.

This screw is supplied directly from original equipment manufacturer for use with Shindaiwa and Echo power equipment/tools. This screw is a standard hardware that has multiple uses depending on your model. Please make sure to check appropriate diagrams for correct location and application for this screw. It is made out of metal and it is sold individually. To secure/loosen this screw you would need a screwdriver.

This spark plug wire, also known as a spark plug coil or spark plug cap coil, is compatible with various makes and models of hand-held outdoor power equipment and is sold individually. This wire is installed within the spark plug boot and attaches to the spark plug for the ignition of your equipment. The spark plug wire is often exposed t...Read moreo extreme heat and excessive vibrations, so through normal wear and tear, it will likely break down. If your equipment is having difficulty starting or has general performance issues, the wire may be the reason why. To replace this wire, make sure your equipment is off before removing the wire and boot from the spark plug. Remove the boot from the wire and install the new wire within the boot before re-installing the boot back to the spark plug.