My Orders
NX58H9950WS Samsung Range - Overview
Models starting with NX58H9950WS
Click on the best match to narrow your results.
Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".
Search filter:
Clear Filter
Your search term must have 3 or more characters.
$17.95
In Stock
Micro Door Switch
Part #3405-001034
This door switch, also known as a safety switch, is a genuine OEM replacement part for microwaves. It is a safety mechanism that sends signals to the microwaves control system, telling it when the door is open/closed. This ensures that the microwave only operates when the door is securely shut and switches off as soon as the door is open....Read more Over time, this switch can become worn out or damaged. A faulty door switch can result in failure to switch the microwave on/off, lack of heat, and running with the door open. To confirm that the door switch is faulty, use a multimeter to test for electrical failure. To remove the faulty switch, disconnect the wiring connectors and take note of where they are positioned. Place the new switch in position and reattach the wiring connectors to the appropriate terminals and close the microwave door to check that the switch engages appropriately.
Read less
$215.55
On Order
Oven Burner Igniter
Part #DG94-00520A
This is an oven burner igniter made for use with Samsung ovens. This oven burner igniter is designed to ignite the gas that flows into it, to produce heat. However, over time and with further frequent use or food contamination, this burner can fail and will need to be replaced. If your burner is glowing red or orange, it is functioning as...Read more intended, but if your oven does not heat up properly, it likely needs replacement. This oven burner igniter is an OEM part that comes by itself and does not come with any of the screws necessary to secure it inside your oven.
Read less
$87.70
In Stock
Range Oven Temperature Sensor
Part #DG32-00002B
This is a range temperature sensor, used to detect the interior temperature of your oven when it is baking or cooking. If you notice your oven is baking unevenly or at inconsistent temperatures, will not start or has too little or too much heat, it is likely that the temperature sensor is bad, or defective. This temperature sensor feature...Read mores a 3.9-inch-long probe, 3.2-inch-long wire harness, and 1.7-inch-wide support bracket. Replacing this sensor is fairly simple but will require a screwdriver, wrench and drill with the appropriate Philips-head bit. Disconnect your range from the wall outlet and pull it out from the wall. Removing your range door is not necessary, but will make removing the sensor that much easier. You will now locate your temperature sensor, which will likely be near the heating element at the top/bottom of the oven. Remove any securing screws holding the heating element and/or sensor in place. At the rear of the range, disconnect and remove the rear panel to gain access to the electronics of the range. Disengage the sensor and its locking tabs, and may also require you to disconnect the terminals for the heating element if your temperature sensor is fastened to it. Remove the sensor and heating element (if necessary). If the sensor is connected to the heating element, use a wrench to unfasten it. Now you install the new temperature sensor and reassemble your oven, ensuring that wire terminals are connected correctly.
Read less
$27.95
In Stock
$7.65
In Stock
Rubber Cushion
Part #DG73-00003A
This rubber cushion is supplied by the original manufacturer and has a shaft approximately 1 inch long. The cushion acts as a layer of protection between the oven door and oven frame/cavity. It prevents heat from escaping and protects the oven door and frame from abrasion and damage. If the rubber cushion becomes brittle or loses its elas...Read moreticity, you will likely notice heat escaping from the appliance, uneven cooking, as well as increased noise, and instability when opening or closing the door. Depending on your appliance model you may need to lift the top oven panel to access the cushion. Pull the faulty rubber cushion out from the oven frame and thoroughly clean the area where the new one will be placed to ensure a good seal. Press the new cushion into position and reassemble your oven to complete the repair.
Read less
$53.51
In Stock
Left Rear Burner Cap - Black
Part #DG62-00070A
If a surface burner clicks but lights poorly or burns more strongly on one side, inspect the cap before replacing other components. A chipped, misplaced, or grease-covered cap can disturb the flame pattern. Lift it off only after the burner is off and cool, then clean and dry both mating surfaces. Also check the burner ports for debris wi...Read morethout enlarging the openings. If replacement is needed, use the complete range model and burner position to confirm fit. Set the cap level on its matching head before replacing the grate. Test the burner briefly, and turn it off at once if flames remain uneven or you smell gas.
Read less
$168.84
In Stock
Bottom Floor Panel
Part #DG61-00570A
This oven cavity floor coating or bottom floor panel is an authentic OEM part supplied by Samsung to ensure compatibility with various models of Samsung ranges. It is a protective layer that sits on the bottom surface of the oven cavity. It protects the bottom surface from direct contact with food particles and provides a smooth, easy-to-...Read moreclean surface that resists staining. The panel is also designed to reflect heat upwards, which helps to distribute heat throughout the oven cavity and ensures that your food is cooked evenly. You should replace this panel if it is damaged, corroded, or has excessive build-up that you are unable to remove.
Read less
$108.95
In Stock
Wire Rack
Part #DG75-01001D
This stainless steel wire rack is a sturdy platform for baking or roasting food, making sure heat circulates evenly. It measures approximately 7/16 inches by 24 3/4 inches and is usually found inside the oven. You can adjust its height using the multiple slots in the oven cavity to suit your cooking needs. Please keep in mind that this genuine OEM replacement part is sold individually.
$51.95
In Stock
Burner Head
Part #DG62-00076B
Weak flames or a burner that will not light can point to a cracked, warped, or blocked burner base. This metal support helps hold the small surface burner assembly in place and directs gas toward the head for steady cooking. First clean the removable pieces and confirm that the burner cap is level. Also check the igniter and nearby connec...Read moretions before ordering a replacement. Verify fit using the full appliance model and burner location because similar bases may differ. Turn off the gas valve, unplug the range, and wait for every surface to cool. Avoid bending the igniter or changing the gas orifice. After installation, confirm an even flame and discontinue use if gas odor is present.
Read less
$82.95
In Stock
Range Surface Burner Cap
Part #DG62-00067A
The burner cap protects the burner head from spills and helps spread out the burner flame for even heating.
$198.95
In Stock
Grate Side Assembly
Part #DG94-00937A
No Longer Available
Bake Igniter
Part #DG94-01012A
The bake igniter is responsible for igniting the gas to light the bake burner within the range. Ensure safety precautions such as shutting off the house circuit breaker and gas supply. Tools Required: Work gloves for hand protection during installation. Additional Information The Samsung Range Bake Igniter (part number DG94-01012A) is an ...Read moreessential component for ensuring reliable ignition of the bake burner in your range. Prior to installation, it is crucial to disconnect the power and gas supply to the appliance to prevent any safety hazards. Wearing work gloves is advised to protect your hands during the process. This part is specifically designed to restore efficient functionality in your range, addressing issues related to the bake burner not igniting properly. Always confirm compatibility with your specific model to guarantee optimal performance.
Read less
Common Symptoms of models starting with NX58H9950WS
How this model fails, and the parts that fix it.
Little to no heat when baking
Fixed by
these parts
these parts
Show All
No heat
Fixed by
these parts
these parts
Show All
Doesn’t shut off
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Oven not heating evenly
Fixed by
these parts
these parts
Show All
Won’t turn on
Fixed by
these parts
these parts
Show All
Oven is too hot
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Watch our pros, then fix it yourself.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!
View More