NX58H5600SS Samsung Range - Parts

This door switch, also known as a safety switch, is a genuine OEM replacement part for microwaves. It is a safety mechanism that sends signals to the microwaves control system, telling it when the door is open/closed. This ensures that the microwave only operates when the door is securely shut and switches off as soon as the door is open....Read more Over time, this switch can become worn out or damaged. A faulty door switch can result in failure to switch the microwave on/off, lack of heat, and running with the door open. To confirm that the door switch is faulty, use a multimeter to test for electrical failure. To remove the faulty switch, disconnect the wiring connectors and take note of where they are positioned. Place the new switch in position and reattach the wiring connectors to the appropriate terminals and close the microwave door to check that the switch engages appropriately.

This is an oven burner igniter made for use with Samsung ovens. This oven burner igniter is designed to ignite the gas that flows into it, to produce heat. However, over time and with further frequent use or food contamination, this burner can fail and will need to be replaced. If your burner is glowing red or orange, it is functioning as...Read more intended, but if your oven does not heat up properly, it likely needs replacement. This oven burner igniter is an OEM part that comes by itself and does not come with any of the screws necessary to secure it inside your oven.

This is a range temperature sensor, used to detect the interior temperature of your oven when it is baking or cooking. If you notice your oven is baking unevenly or at inconsistent temperatures, will not start or has too little or too much heat, it is likely that the temperature sensor is bad, or defective. This temperature sensor feature...Read mores a 3.9-inch-long probe, 3.2-inch-long wire harness, and 1.7-inch-wide support bracket. Replacing this sensor is fairly simple but will require a screwdriver, wrench and drill with the appropriate Philips-head bit. Disconnect your range from the wall outlet and pull it out from the wall. Removing your range door is not necessary, but will make removing the sensor that much easier. You will now locate your temperature sensor, which will likely be near the heating element at the top/bottom of the oven. Remove any securing screws holding the heating element and/or sensor in place. At the rear of the range, disconnect and remove the rear panel to gain access to the electronics of the range. Disengage the sensor and its locking tabs, and may also require you to disconnect the terminals for the heating element if your temperature sensor is fastened to it. Remove the sensor and heating element (if necessary). If the sensor is connected to the heating element, use a wrench to unfasten it. Now you install the new temperature sensor and reassemble your oven, ensuring that wire terminals are connected correctly.

This stainless steel knob dial on your range allows you to control the temperature and function of your range. It is found on the front panel. If it is difficult or impossible to adjust the heat settings, it is time to replace your knob dial. It can easily be pulled off and popped into place. Since this genuine OEM dial is sold individually, check how many you need before getting a replacement.

The Black Leveling Leg from Samsung is a durable, genuine part designed for use with many Samsung kitchen appliances. This quality leg-leveling device offers an easy-to-use design to correct uneven surfaces, promising consistent performance to ensure your appliance is always level and stable. Carefully crafted by Samsung, it is compatible...Read more with select Samsung Range models. This component helps support your appliance, with adjustable height for seamless alignment. Upon purchase, rely on your owner's manual for detailed installation guidelines. Choose Samsung for reliable, long-lasting appliance parts.

This surface burner cap is specially designed to fit with Samsung ranges. It is a genuine OEM replacement part supplied directly by Samsung to ensure compatibility. The burner cap is a round, black cap that has a diameter of approximately 1.75 inches. It covers the burner head and helps to distribute the flame across the burner to ensure ...Read moreyour food is cooked evenly. The cap also protects the burner head from accidental food spillage and debris to keep your range running efficiently. The burner cap will need to be replaced if it is cracked or can no longer remain securely attached to the burner head. Each cap is sold individually.

This rubber cushion is supplied by the original manufacturer and has a shaft approximately 1 inch long. The cushion acts as a layer of protection between the oven door and oven frame/cavity. It prevents heat from escaping and protects the oven door and frame from abrasion and damage. If the rubber cushion becomes brittle or loses its elas...Read moreticity, you will likely notice heat escaping from the appliance, uneven cooking, as well as increased noise, and instability when opening or closing the door. Depending on your appliance model you may need to lift the top oven panel to access the cushion. Pull the faulty rubber cushion out from the oven frame and thoroughly clean the area where the new one will be placed to ensure a good seal. Press the new cushion into position and reassemble your oven to complete the repair.

Enjoy the precision and durability of Samsung with this high-quality Left Rear Burner Cap. Known as the "surface burner cap", this essential component is designed to cover the surface burner of your Samsung range. It serves as a protection against drips and splatters during your cooking sessions, enhancing longevity of your appliance whil...Read moree maintaining a clean, sleek look. This burner cap also assists in evening out the flame from the burner for consistent heating. Easily installable, this genuine Samsung part plays an intrinsic role in keeping your range functioning smoothly. Incorporate it today to ensure your Samsung range stays in pristine condition for your culinary adventures.

This oven cavity floor coating or bottom floor panel is an authentic OEM part supplied by Samsung to ensure compatibility with various models of Samsung ranges. It is a protective layer that sits on the bottom surface of the oven cavity. It protects the bottom surface from direct contact with food particles and provides a smooth, easy-to-...Read moreclean surface that resists staining. The panel is also designed to reflect heat upwards, which helps to distribute heat throughout the oven cavity and ensures that your food is cooked evenly. You should replace this panel if it is damaged, corroded, or has excessive build-up that you are unable to remove.

This stainless steel wire rack is a sturdy platform for baking or roasting food, making sure heat circulates evenly. It measures approximately 7/16 inches by 24 3/4 inches and is usually found inside the oven. You can adjust its height using the multiple slots in the oven cavity to suit your cooking needs. Please keep in mind that this genuine OEM replacement part is sold individually.

The Samsung Burner Head (Aux) is a top-notch enhancement for your Samsung range. Specifically designed to endure high temperatures, this quality part, crafted from sturdy metal, ensures durability and maximum performance. It tightly holds the orifice and properly directs gas to the burner head for consistent and precise heat dispersion. T...Read moreo maintain safety, ensure the gas is shut off and the burner is cool prior to installation. Wearing gloves can provide additional protection for your hands. This impressive Burner Head (Aux) from Samsung not only ensures optimal functioning of your range but also enhances your cooking experience to a new level.

The burner cap protects the burner head from spills and helps spread out the burner flame for even heating.