NV51T5511DG ((AA)(0000)) Samsung Wall Oven - Parts

This is a range temperature sensor, used to detect the interior temperature of your oven when it is baking or cooking. If you notice your oven is baking unevenly or at inconsistent temperatures, will not start or has too little or too much heat, it is likely that the temperature sensor is bad, or defective. This temperature sensor feature...Read mores a 3.9-inch-long probe, 3.2-inch-long wire harness, and 1.7-inch-wide support bracket. Replacing this sensor is fairly simple but will require a screwdriver, wrench and drill with the appropriate Philips-head bit. Disconnect your range from the wall outlet and pull it out from the wall. Removing your range door is not necessary, but will make removing the sensor that much easier. You will now locate your temperature sensor, which will likely be near the heating element at the top/bottom of the oven. Remove any securing screws holding the heating element and/or sensor in place. At the rear of the range, disconnect and remove the rear panel to gain access to the electronics of the range. Disengage the sensor and its locking tabs, and may also require you to disconnect the terminals for the heating element if your temperature sensor is fastened to it. Remove the sensor and heating element (if necessary). If the sensor is connected to the heating element, use a wrench to unfasten it. Now you install the new temperature sensor and reassemble your oven, ensuring that wire terminals are connected correctly.

This is a high limit thermostat designed for microwaves, ranges and ovens. Made of plastic and metal, this thermostat is designed to open the electrical circuit for your appliance when it reaches a specific internal temperature. In some cases, high limit thermostats can become defective and if your appliance will not turn on, or has a spe...Read morecific error code, it must be replaced. This thermostat is a genuine OEM part that is sold as an individual part and can be replaced by disconnecting the appliance from the power, and accessing its panel, usually located near the bottom of your range, or wherever the heating element is located. Reference your user manual for exact location and replacement instructions.

This rubber cushion is supplied by the original manufacturer and has a shaft approximately 1 inch long. The cushion acts as a layer of protection between the oven door and oven frame/cavity. It prevents heat from escaping and protects the oven door and frame from abrasion and damage. If the rubber cushion becomes brittle or loses its elas...Read moreticity, you will likely notice heat escaping from the appliance, uneven cooking, as well as increased noise, and instability when opening or closing the door. Depending on your appliance model you may need to lift the top oven panel to access the cushion. Pull the faulty rubber cushion out from the oven frame and thoroughly clean the area where the new one will be placed to ensure a good seal. Press the new cushion into position and reassemble your oven to complete the repair.

This terminal block assembly is designed for use within various models of ranges and is sold as an individual OEM part without any other hardware included. Terminal blocks are responsible for receiving, managing, and distributing the power within an appliance. Electrical shorts or surges can cause this terminal block to overheat and melt ...Read moreand become inoperable, thus needing immediate replacement. If you smell melting plastic when operating your range, turn it off and disconnect it from power immediately and inspect this terminal block and all other electrical components. To replace this terminal block, disconnect your range from the power and remove it from the wall. Remove the back panel of the range and locate the terminal block, making note of its wire configuration. Unscrew the wires and the ground wire if there is one, and then do the same for the mounting screws. Install the new terminal block in the same position as the previous one, attaching all necessary wires as they were originally, before you reconnect and reposition the range.

This flange nut is designed for use within various cooking appliances like ranges, microwaves and wall ovens. Flange nuts are typically used to evenly distribute pressure across its application surface, and can also eliminate the need for a separate washer. This flange nut also features a ribbed surface on the flat side, so it can bite in...Read moreto the mating surface to create a more secure connection. Since this nut is not used for one specific purpose, its use is versatile, and it can be used in a variety of applications. This nut is a genuine OEM part made of high-quality metal, and a wrench is the only tool you will need to install or remove this flange nut.

This door latch assembly secures the door in place during operation. Designed for consistent engagement, it helps ensure safe operation and proper sealing.