NJSR453EW1AA Hotpoint Dryer - Instructions

The end repair was very simple and took minimal effort. The time and difficulty was all in the testing. I disassembled the dryer and removed the drum and then hard wired each thermo-fuse to determine where the fault was. After test all of those I was stumped. When I opened the door the light would not come on so I assumed it was a pow ... Read more er fault closer to the source. However after all of my testing I couldn't find anything wrong. I then removed the light bulb and realized it was burned out which led me to the door switch being the fault. I removed the switch and soldered the three wire together and the dryer started right up! All I had to do was order a new $15 part, unsolder the wires and plug them in. Would have been so much simpler if that light bulb hadn't of been burned out causing me to over think my diagnosis. This was my first major appliance repair and I did it with only the help of the parts diagram provided on the website.

Doing some simple troubleshooting with the volt-ohm meter I determined that the door switch was failed.

The replacement door switch restored the motor circuit keeping my dryer in action.

The problem was intermittent. It only happened when the unit was first started. After it was restarted it usually worked until the load was dry. I looked at the schematics and saw that only the hi-temp therostat and the motor overload could stop the dryer completely. I put my volt meter on the hi-temp thermostat and ran the dryer. Wh ... Read more en the dryer stopped I realized the hi-temp therm. was tripping. I read the web site help for this symptom and the suggestion was the bias therm.
I replaced it and the unit worked.

Removed case parts to expose internal wiring. Vacuumed up various types of mouse debris and plugged hole they were using. Ordered terminal block to replace the one that melted while sparks were flying. Replaced power cord with one I had in my basement from some other appliance that died a while ago. "Hey honey, ya know those old parts I s ... Read more aved..." :) Now it is heating to capacity and no spark-show! Oh yeah, the part I ordered from Partselect.com was delivered to my door the next day!!!!! Wow!

I wanted to fix the cheapest possible problem first which was the thermostat.

Got the dryer apart and it was the wrong thermostat for the dryer, which was good news! I looked in inside floor of the dryer cabinet and saw alot of tiny "springs". Couldn't figure how they got there.

Turned out they were coils from t ... Read more he heating element. Must have burnt out and fell free from the element. So I ordered that and replaced it.

I want to say that I'm in NJ and I ordered that thermostat and got it in ONE DAY! Thought that was too good to be true but when I ordered the heating element THAT CAME IN ONE DAY!

I don't know what kind of people work in the shipping department but they are awesome! You really made the difference on this job.

So did the info on your website. I've never even seen a dryer apart before. It was a piece of cake thanks to you guys. You just saved me about $500.

First unplug dryer to prevent electrical shock. To remove the front of the dryer, open the door in top left and top right corners is a machine screw. They can be removed with a Phillips screw driver. Lift the top slightly and let front fall forward about 6 inches, lift slightly. Two wire will be connected to the switch in the door. remove ... Read more the wires and squeeze the tabs on both sides of the switch and push it out. Push new switch in to replace old switch and reassemble.

I first unplugged the unit, opened the top, disconnected and took off the control panel, took off the front panel to determine the source of the squeaking noise coming from the Dryer. I saw that 3 of the 4 Front Drum Glides were gone and the drum had worn away significant amounts of plastic from the Top Bearing Assembly. I purchased the ... Read more Top Bearing Assembly and a set of 4 Front Drum Glides. Disassembled the damaged parts and reassembled with the new replacement parts. The reassembly took less than 20 minutes. I plugged in the Dryer and viola! It works as good as new.

Pulled the unit all apart to replace the rear drum bearing. Also replaced the front bearing. Works like brand new. Easier then I thought

When the dryer was installed last year by the dealer, one of the hot leads was not screwed down tightly. Over time the screw loosened and began to arc causing the plastic holding the screw to melt. When I moved the dryer the hot lead fell off and hit the terminal block cover shorting out the dryer. I was able to locate the exact terminal ... Read more block I needed with their helpful dryer section diagrams. The part came in the time they said. I took off the old terminal block with just 2 attached screws. i kept track of which screws held the hot and neutral conductors and the ground before I removed them. I was then able to slide on the dryer wires and attached the home conductors. I put on the cover plate, turned on the circuit breaker and it worked.

Open the door and removed the part. Installed the new part and started the dryer.

Unscrewed the old, screwed in the new making sure wires matched up same as before. Reset my breaker and works like new again.

Removed 2 screws to remove top. Removed 2 other screws to remove front. Removed old parts. Installed new parts. Reassemble all afetr cleaning duct work out.

took off top of dryer, took out 2 screws so front of dryer could be removed, replaced bearing,slides and felt seal

pulled off the top, pulled off the front then replaced the plastic that was supporting the front side of the drum. fairly easy to replace although the little plastic 'slides' (you need 4 of them)

Initially purchased just the plastic slides, but when I opened the dryer I found the top drum bearing was smashed and the plastic was basically gone in a whole section, so I then ended up ordering the bearing as well. If you hear the loud squeaking, just buy the top drum bearing and the 4 slides (two white and two dark green). It is an ... Read more easy repair and the squeaking sound is gone.