NDU4J Norge Dishwasher - Instructions

My husband removed the screws that hold the inside panel in place to expose the contral panel area. He disconnected the wire connections and removed the part to replace. One of the relay housings cracked and he had to glue it back together before he could reassemble the whole thing. I did not include drying time in the repair time estimat ... Read more e. After reassembly, the dishwasher worked like a charm.
Many thanks to PartSelect.com and my husband!

I determined that the problem was the door switch after disassembling the door and noting a broken electrica switch. After receiving the new part, I replaced the whole door switch assembly, and the dishwasher turns on and works fine.

At first I tried putting the spring into the lid where the shorter extension of the spring fit tightly into the recessed part of the lid. (If you look at the lid where the hole is for the spring and pin, you see that there is what looks like the arm of the letter "Q".) This worked, but the lid would only open with limited force and would ... Read more hang down when the dishwasher door was closed.
After looking at it again, I positioned the spring so that the shorter extension of the spring ran through the partially open portion of the spring hole. (Looking at the cup laying flat on the ground, you see that the bottom of the pin/spring hole has a slit in it). This allowed the spring to have greater tension and I have had no more problems. The lid opens with force and stays closed when the dishwasher door is closed (vertical).
This may be a little confusing as I do not know the technical terms for any of this stuff, but I just mess with stuff til it works or breaks, whichever comes first! haha

With watching Video on line it was fairly simply, my son knew exactly what to do, it took him about 20 minutes from start to completion and when tested, dishwasher ran great. We have used it six times and have not had a problem. I would highly recommend this part if you are having the same problem. The video was very good.

Took off the lower front plastic piece and unscrewed the side panel to snap the new part in place then attached the spring to it.

From other comments on this site, I learned that 2 people fixed the problem with a new door gasket; 3 fixed the problem by replacing the dispenser latch. I tried the gasket and it helped some (obviously needed replacement anyway) but then learned that the rubber boot around the soap dispenser latch was torn into two pieces. Replaced it ... Read more and good-to-go.

After checking out the mechanism, I realized that the wax motor which operates the dispenser was no longer working. I conatacted Part select and on the second day, on a Saturday, Fedex delivered the little wax motor. I simply separated the front panel with the inside panel with 7 screws and a 1/4 inch nut driver. I slipped out the old wax ... Read more motor, unclipped the two wires and slipped in the new motor. Attached the wires and put the panels back togehter. Voila, the dispenser works perfectly.
Total time, 15 minutes.

They just snapped in to place. Once I realized where they went. They are not the exact rollers needed but will do until I get the right ones. The rack will not come out as far as it should because of the difference. Other than that....easy.

I removed the inside panel. This exposed the rear of the control panel. I carefully replaced the defective switch. Only one was bad but of course i replaced both.

I pulled the unit out its bay and saw that one spring was missing. I looked up the parts online and ordered replacement springs and linkages. Using the existing spring and linkage as models, I easily installed the new parts. I ordered spare parts in case the other linkage broke.

USED A STAR SCREWDRIVER TO REMOVE THE LOWER SCREEN THEN REMOVED THE SUPPORT NUT BY HAND REPLACED THE LOWER SPRAY ARM & SCREEN WORK BETTER THAN EVER.THE ONLY NEGATIVE WAS THE PART TOOK 10 DAYS TO ARRIVE .

Removed 2 each screws from counter top. Pulled washer out 1'. Installed springs and linkage by hand with door closed. Push washer back reinstalled 2 screws.

Used your web site was able to identify correct part very quickly. Received the replacement part in 2 days.
Removed broken part with screw gun only took 20 minutes. Was very please with ease of site and quick delivery.
Thank you

Just slide the old upper dishrack forward to the end. The stops on either slide must be removed . Only difficulty was getting the plastic stops to open up. We used a thin metal knivre to wedge into the opening.

Removed front access panel
Disconnected water supply
Pulled dishwasher out approximately 1 foot to gain access to spring linkage
Connected new spring linkage to spring, connected other end of spring linkage to door
Tested operation of door
Slid dishwasher back into place, reconnected water supply and front access ... Read more panel