My Orders
- Home
- MWS445RFS2
- Instructions
MWS445RFS2 Frigidaire Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Cold water was filling slower than the hot water.
0 of 1 people
found this instruction helpful.
-
Steve from Fort Mohave, AZ
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Pulled out the machine. Disconnected water lines. Removed four screws attaching the top brackets. In rear of top panel. Slid top panel forward and clear of valve. Removed two wire harnesses. Removed two screws holding valve to the back panel. Pulled valve down and out. Removed outlet side line spring clamp with channel lock pliers and pul
... Read more
led hose off old valve. Installed outlet side hose and spring clamp onto new valve. Placed valve up into place and installed two screws. Installed two wiring harnesses. Replaced top lid. Replaced lid bracket screws. Re-attached water hoses and pushed the machine back into place.
Read less
Was this helpful?
Thank you for voting!
motor burnt out
2 of 7 people
found this instruction helpful.
-
ANNA from STATEN ISLAND, NY
- Easy
- 15 - 30 mins
-
Wrench set
my husband did the work he can fix anything.i watched he explained what he was doing and how he was getting it done.it did"nt take long at all.the biggest problem was setting the belt tensioner . its running great!!!!!!!!!!!!!!!!!!!!
Was this helpful?
Thank you for voting!
broke hose
1 of 4 people
found this instruction helpful.
-
jose angel from dalton, GA
- Easy
- 15 - 30 mins
-
Screw drivers
disconneted power removed two screws removed led the front clamp removed quiet hose remplace for new
Was this helpful?
Thank you for voting!
No cold water supply
0 of 1 people
found this instruction helpful.
-
Harold from Kansas City, MO
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Removed two screws that held top of washer in place. removed top of washer. Removed two screws that held water inlet alve in place. Removed clamp and outlet hose from old inlet valve.
... Read more r />
Removed two screws hold wash machine cover in place. Removed cover. Unscrewed cold and hot water supply lines from old inlet valve. Removed two screws holding inlet valve in place. Removed clamp and hose from inlet outlet hose. Replaced inew inlet in reverse order.
... Read more r />
Removed two screws hold wash machine cover in place. Removed cover. Unscrewed cold and hot water supply lines from old inlet valve. Removed two screws holding inlet valve in place. Removed clamp and hose from inlet outlet hose. Replaced inew inlet in reverse order.
Read less
Was this helpful?
Thank you for voting!
No hot water in machine
0 of 2 people
found this instruction helpful.
-
julie from minneapolis, MN
- Easy
- 15 - 30 mins
-
Nutdriver, Wrench (Adjustable)
First I removed the hot and cold water supply lines to the machine. Then I removed the two screws at the top of the back panel, and pulled the entire top of the machine off which was a little tricky to figure out. There are two tension-like clips in the front of the machine holding the top on. (I had thought the back panel would come o
... Read more
ff so I was surprised when it became clear that the top of the machine would come off.) Then I unscrewed the two screws that hold the water inlet valve. I had to remove the green grounding wire that was clipped on the frame. The water inlet valve then lifted out easily. There were two clips to slide off, and a hose going into the tub that also had to come off which I did by loosening a little clamp on the end of the hose- saved the clamp for the new valve! Re-attaching everything was a snap. Tested the hot water before re-setting the top of the machine back together and it worked!
Read less
Was this helpful?
Thank you for voting!
water not turning off
0 of 2 people
found this instruction helpful.
-
Anita from Orange, TX
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Wrench (Adjustable)
Two small clamps holding the top onto the body were removed with two screws. I lifted the top and held it up with a small piece of board. Two screws were removed on the back top left that hold the water inlet valve in place. Once those were removed I reached inside and removed the two plugged in wires and and lifted the part out. At this
... Read more
point I used pliers to unclamp the hose that fed into the washer. I then reversed the process and put in the new part. Works great. Thanks a lot for making the part I needed easy to find. I am now a true fans of your website.
Read less
Was this helpful?
Thank you for voting!
Water would not shut off
0 of 2 people
found this instruction helpful.
-
Todd from Eagle River, WI
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Unplug washer. Remove supply lines. Remove two screws in back and remove clips holding top of washer. Front of washer top is held by two clips. Release top from clips and slide top towards the front. Remove two screws holding the water inlet valve to the back of the washer. Lift unit out and remove clamp and hose. Install new unit in reve
... Read more
rse of removal.
Read less
Was this helpful?
Thank you for voting!
Front load washer continued to fill with water until door failed. Major Flood
0 of 2 people
found this instruction helpful.
-
Malcolm from Shelley, ID
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Removed screws at back securing top panel (4).
Removed screws holding water inlet valve to back of machine (2)
Removed water hoses to bucket
Removed squeeze clamp securing water distribution hose from inlet valve
Reversed method with new valve.
Very fast...~25 min
Works fine so f ... Read more ar!
Removed screws holding water inlet valve to back of machine (2)
Removed water hoses to bucket
Removed squeeze clamp securing water distribution hose from inlet valve
Reversed method with new valve.
Very fast...~25 min
Works fine so f ... Read more ar!
Read less
Was this helpful?
Thank you for voting!
water dripping into the tub when off
0 of 2 people
found this instruction helpful.
-
George from St. Louis, MO
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Shut off water to washer....unplug power cord...pulled washer from wall out into room....removed 2 water supply hoses....removed 2 top retaining clip screws on rear top of cabinet.....lifted rear end of top panel up approx 5 inches......propped up with small pieces of cut up 2X4 lumber.....did not disconnect any wiring related to the co
... Read more
ntrol panel...remove 2 screws holding valve to cabinet back panel......lift valve up and out of cabinet by the tub fiil hose.....disconnect 2 wire plugs, mark these upper, lower or hot /cold......disconnect the tub fill hose....remove the back panel-to-valve bracket off the old valve and install on the new valve and reverse this procedure!!! The new valve flows water better and faster, the wash is done quicker!!
Read less
Was this helpful?
Thank you for voting!
water would not shut off causing door to pop open and spill all over the floor
0 of 2 people
found this instruction helpful.
-
Joe from Interlaken, NY
- Easy
- 1- 2 hours
-
Pliers, Screw drivers
The repair would have gone much easier if I did not have a stack dryer on top of the washer. Had to roll out the total unit and work with the dryer partly on top. Only needed minimal work and tools after that.
Was this helpful?
Thank you for voting!
Drain Hose Leak
2 of 9 people
found this instruction helpful.
-
Colby from College Station, TX
- Easy
- 30 - 60 mins
-
Pliers
Unhooked old hose and replaced with new one.
Was this helpful?
Thank you for voting!
Replace water inlet valve.
-
James from Lutz, FL
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Took off back of washer. Control panel and top. Disconnected hot and cold water inlet hose. Pulled offwire leads. Unscrewed valve from washer. installed new valve. Reconnected wire leads. connected hoses. put top back on. put back of washer and control panel back on. Reconnected water. Done. Nothing too difficult. just a littl
... Read more
e time consuming. Space was an small issue in the laundry room.
Read less
Was this helpful?
Thank you for voting!
Washer would drain most the time but not spin
-
Johnny from Providence, NC
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
This is a front loader and the video I saw was a top loader. I removed the oval shaped centerpiece off the back to reach the pump. I also removed the filter and cleaned it, I used screw type hoseclamp in place of the tension spring for easier assembly due to the cramped space. This helped the drain problem as did cleaning the filter. The
... Read more
no spin problem persisted and I ordered the door lock part. This part fixed the no spin problem.
Read less
Was this helpful?
Thank you for voting!
Washer leaked at water inlet valve
-
Joel from Eugene, OR
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
The part was fine,except for one problem. The screw holes in the part were too small for the sheet metal screws. After several minutes of trying to get the screws to turn, I got a small round file and enlarged the holes until the screws fit. Luckily for me, I've had to do things like that before. Otherwise, the installation was straightfo
... Read more
rward. And the washer no longer leaks!
Read less
Was this helpful?
Thank you for voting!
she would not rattle and roll
-
michael from minneapolis, AL
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
I met her in the basement lonely and needing a fix i went down on my knees and started to take off her worn out belt slowly down past her pulley and off her soon to be hot transmision. i gently held her pulleys as i wrapped her new belt around them. putting her chasies back together and plugging her in i pushed her button and off she went
... Read more
shakening and rallting once again.
Read less
Was this helpful?
Thank you for voting!