MWS445RFS0 Frigidaire Washer - Instructions

Replacing all springs. Able to replace 2 short springs and front spring. Can't get to ones in back of washer tub. Unable to use strenght in arms to remove old springs. Help videos were great. Saved money by doing repairs myself.

After not being able to get the proper 10 foot hose, and having to splice two drain hoses together....turned out it was not the drain hose after all, but the pump. Some sort of "baffle" in the drain hose, where the rubber connector at the pump end and the corrugated hose joins, was blocking the water I thought. It may have been since a ... Read more spliced the new hose in at that end. However, I think it was the pump.

I followed the following instructions provided by the parts page and they were EXCELLENT! I had NO problems and was actually enjoyable to fix, thx. to these instructions listed below. Many thanks!!!! FIRST I REMOVED THE TOP PANEL HELD BY FOUR SCREWS AT REAR OF PANEL, PULLING THE PANEL FOWARD AND UP. THEN DISCONNEC ... Read more TED THE POWER AND WATER CONNECTIONS. THEN I REMOVED THE TWO SCREWS HOLDING THE FLOW VALVE TO THE WASHER REAR PANEL,PULLED THE VALVE FOWARD ,REMOVED THE TWO ELECTRIC CONNECTORS, PINCHED THE WATER CLAMP WITH PLIERS AND REMOVED THE WATER CONNECTION TO THE VALVE. THEN REPLACED WITH THE NEW VALVE FOLLOWED THE ABOVE STEPS IN REVERSE ORDER, FINISHING UP BY RE PLACING THE WATER CONNECTIONS AND POWER. THEN CHECKED FO PROPER REPLACENENT AND LEAKS BEFORE REPLACING TOP PANEL

part was fast easy to put on know work better then before

i took the hose of and stuck the water hose in it and saw a lin hole leak. i order a new hose and recived it very fast (1 day) took 15 min to put it on the pump and to put the machine back togther

Part came in, fast delivery. Took 10 minutes to install. Real easy works great.
Thanks PartSelect.

At first I thought the o-ring may have wear out so I took the pump out to check, but the leak was either from the shaft seal or body itself (hard to tell as body had corrosion on it) taken out the pump was very easy, but you need to use the right pliers to easily remove the spring clamps. Follow instruction to set the housing orientation ... Read more , and than install back the pump. Reinstalling one of he hoses using the spring clamps took few tries, but it was in place in no time. remember not to install the cover before you operate the washer to verify no leaks. This work is realy very very easy.

1. Turned off water to washing machine.
2. Used plyers to disconnect the hoses at the back of the washer.
3. Unscrewed old inlet valve from back.
4. Opened top panel of washer and disconnected hose running to wash basin.
4. Lifted the old unit out and unplugged electrical wiring.
5. Reverse above and you're finis ... Read more hed!
If you're reading this you can probably do the repair.
Saved myself $500+ on a new washing machine. Wife is happy.

I had to remove agitator and clean under it.

This is the third time it has been replaced. They last about 2-3 years. Made sure pump was full of water before starting etc so we didn't start with a "dry" pump.

The actual repair and parts ordering went just fine.

Scotty

Replacing the pump assembly only involved:
1. Unplugging the washing machine!
2. Removing 2 screws to take off the washing machine's lower front panel.
3. Removing 2 bolts to take off the cover over the remote pump assembly.
4. Changing out the pumps required:
A. Unscrewing the 2 screws that secure the assembly ha ... Read more rness to the washing machine's base.
B. Unclasping the 2 tubes using curved jaw pliers.
C. Disconnecting the electrical connectors by hand.
D. Removing 2 bolts from the assembly harness and the pump assembly.
5. Reverse steps 1 - 4 to install the new pump.

Removed two screws that held top of washer in place. removed top of washer. Removed two screws that held water inlet alve in place. Removed clamp and outlet hose from old inlet valve.
























... Read more r />


















































Removed two screws hold wash machine cover in place. Removed cover. Unscrewed cold and hot water supply lines from old inlet valve. Removed two screws holding inlet valve in place. Removed clamp and hose from inlet outlet hose. Replaced inew inlet in reverse order.

Read less