MW96T (P1178808M) Amana Microwave - Instructions

Remove top grille (2 screws), undo control panel (1 screw). Tilt down control panel, switches are on the left. There are actually three switches that are involved with the door, two horizontally mounted, one vertically mounted. This would be an EASY REPAIR, but it took me a while to figure out which of the three switches was bad, and a ... Read more lso took a while to figure out that there is a plastic rod that inserts through the hole in the switch body. Once i figured this out went like a breeze. Lower horizontal switch was the bad one, but since the kit came with two switches i went ahead and replaced the upper horizontal one as well. IT appears that the horizontal switches are probably more likely to fail than the vertical switch based on the position of the switch and force angles. Works great now!

I removed the unit from the wall. Took the cover off. Set the unit on its side. It revealed the working parts. Removed the old micro switches. Put in the new oness. Presto, it worked. Very easy for me.
The parts was delivered almost before my notice they were shipped.

1. Removed cabinet screws (10-15?). 2. Removed cabinet. 3. Removed top interlock switch which actually was not defective. The press clip connection appeared as if it had been arcing for quite some time and the corrosion created resistance sufficient to prevent the current from getting through the switch. 4. Replaced switch anyway but brok ... Read more e plastic retaining clip despite every effort not to do so. Reset broken clip with super glue. 5. Reassembled cabinet and appliance is in good working condition.

Problem would come and go. Found service schematic inside unit. Perform all the suggested tests. One possible solution was the primary interlock switch shown on the schematic and a check found the switch stuck. It would free up some times but would stick again in the open position. Ordered switch which was a simple plug in unit.

Found instruction on internet,
1. Remove anit-tampering screws with punch and hammer
2. Remove the rest of the screws
3. Removed cover
4. Remove burned out bulb and installed new one
5. INstalled cover
6. Installed screws including the anti tampering onces
7. Op tested unit.
Wife is happy.

We have a Jenn-Air microwave and oven combination that is installed as a "stack" in a cabinet. The light bulb had burned out, and I read some of the posts on the partselect.com site about how others performed this replacement; ours was a bit different.
To replace the microwave light bulb, we had to remove the entire microwave and ... Read more oven stack from the cabinet. There were four anchor screws on the sides (two on each side) of the microwave that were driven in perpendicular to the face of the microwave. There were four more screws that were on the sides of the oven that could be accessed once the oven door was open.
With those anchor screws removed, we had to carefully pull the entire microwave / oven stack from the cabinet to reach the top cover of the microwave. We used an old wooden crate to hold the front of the oven and left the back of the oven resting in the cabinet enclosure. This gave enough room to access the screws on the top cover of the microwave, without having to lift the entire stack down to the floor.
At this point, I could unplug the microwave power cord, which was plugged in to a socket built into the top of the conventional oven part of the stack.
The top cover of the microwave was attached with regular Phillips head screws, so those were easy to remove. Several other instructions indicated I would need a torx or star drive screwdriver, but I did not.
Once the screws were removed from the top cover of the microwave, the cover can slide rearward to be removed. However, there are two metal strips that run vertically along the sides of the microwave and at the top of the microwave, these bends over at a right angle over the top of the microwave. The top cover has tabs that sticks up vertically from the cover, so that the bent strips prevents the cover tabs from passing as the cover is slid backwards. The vertical strips have several screws connecting it to the body of the microwave. On one of the vertical strips, I removed the two of these screws closest to the top of the microwave. Then, I gently pushed a wood chisel, because of the bevel angle, between the vertical metal strip and the microwave body. This moved the bent-over portion of the vertical strip far enough away from the microwave that the tab on the top cover cleared the strip, and I could then remove the top cover.
With the top cover removed, I could see the old light bulb. It is attached with a push-in electrical connection that was easily pulled off. One Phillips head screwdriver held the old bulb in place towards the rear of the microwave. Towards the front of the microwave, a small plastic post holds the front of the bulb. I removed the screw and pulled out the old bulb.
The new bulb fits easily into the same plastic post and screw connection. However, the new bulbs connector prongs are bent at a 90 degree angle to the original bulb. Instead of sticking straight out from the microwave, which was how the old bulb was configured, the new bulb prongs pointed to the right side of the microwave (as viewed from the front). Fortunately, the wiring harness in the microwave that connects to the light bulb had a zip tie that was loose enough to get enough slack for the push-in connector to reach the new bulb's prongs.
After the bulb was in, I reversed the steps described above, making sure to leave the chisel in place until the top cover had been secured back in place. Once the chisel was removed from the vertical metal strip, the bent portion again would prevent easy removal of the top cover. I made sure to plug the microwave power cord back into the outlet on the conventional oven, then we slid the entire unit back into the cabinet enclosure, and I put the anchor screws back to hold the stack into the cabinet.
Three of us worked on this - mostly to help pull the stack out of the cabinet and to help steady it while the front was resting on the wood crate. This is not a single-person job. It was not terribly difficult, but the number of steps is very tedious. I found a helpful YouTube video "How to uninstall/install a Jenn-Air JMC8127DD/JMC8130DD Microwave Oven" posted by Ali The Handy Man. Being able to see that the microwave and oven stack was connected by a "bridge" (as Ali calls it) was a major help in tackling this.
After this, we suspect that Jenn-Air must have not wanted any repairs to their appliances. As I said above, this repair to replace a light bulb seemed unnecessarily tedious.

remove outer cover of microwave, (special recessed star bit required) change bulb, unplug and remove 1 phillips screw.

There were two hard parts for me to work through.

The first was breaking off the two screws that need a special head screwdriver to remove. None of my special special head screwdrivers worked (I have a few), so I used a hammer to force them off.

The second hardest part for me was finding the correct replacement bulb ... Read more on-line. My Amana Microwave is a combo Microwave/Convection type, and it's a strange little bulb - almost tube like.

Once I did find the right bulb on this PartSelect.com website it was a breeze. The part was delivered in just a couple of days (even during this Covid-19 pandemic). Once I had the replacement bulb in hand it barely took 5 minutes to install.

Thanks PartSelect!!

1. Order correct light bulb for unit and have it with you before removing old lightbulb.
My Microwave is built into cabinet.
2. Disconnect power (Either turn breaker off or unplug unit from wall)
3. Remove face cover on cabinet. (4 Phillips head screws)
I was able to reach in the opening in the cabinet and unplug from ... Read more the wall.
4. Remove Phillip head screws holding microwave in cabinet.
5. Remove microwave from cabinet.
6. Remove Phillip head screws and torx screws holding outside cover on the back of unit and the side (1 on right side) and then remove cover.
Light bulb is on the top front right side.
7. Remove 1 philip head screw holding light bulb and unplug quick connector wires.
8. Plug quick connector into new light bulb same way it came out and place new light bulb in place and put the 1 philips head screw holding it back in place.
9. Put cover back on and all the screws. Temporary plug the unit in to test light bulb works before securing it back into cabinet.
10. Reverse order 5,4,Plug unit in wall before putting the face back on.
Done.

Watched a you tube video prior to installing new switch. Followed the video which gave me confidence i was up to the task. After removing the touch pad I found my design was not exactly like the you tube model but I found the defective switch, replaced it and put the microwave back together. Works great. Again watch the videos

Required that i remove the built in frame and mounting. Required tamper proof socket to remove housing. I removed the old bulb and simply replaced and reverse installed the cabinet.

All the electrics worked on Amana microwave EXCEPT for the cooking function. Inspected the control board and found the upper switch on the door interlock was burnt. Installed new switch in minutes and everything now works fine. Unfortunately, had to purchase expensive two switch "kit" although only one switch was kaput. PartsSelect mai ... Read more ling was SUPER fast. Thanks for looking, Scott

"PIECE OF CAKE" Removed cover,removrd bulb, replaced bulb, replaced cover. "PIECE OF CAKE" P.S. Wife is happy.

Since others reported similar problems and it was just the fuse we tried that first. That wasn't the problem so we ordered the Door Interlock Switch Kit. Shipping was very fast! Our microwave had 3 switches. My husband asked how to know which one to switch. I read that one person just did process of elimination. Luckily ours worked ... Read more on the first change out! So happy to have stumbled across this site and not have to buy a whole new microwave.

remove 4 screws from top, front louvered panel snaps out. remove 1 screw from top of keypad, keypad pivot's forward and can be removed. There is a white mounting bracket inside left. Remove two screws, one top and one bottom, bracket lifts up and out. 3 sets wires are attached, mark them with masking tape, top, center, bottom and pull out ... Read more plugs. They can only attach one way. Using a very small screw tip, lift plastic latch from switch, it rotates out and is removed from the pivot pin. reassemble in reverse order after switches are replaced