MW84 Microwave - Instructions

very easy

Screwed in light bulb and glass protector

removed two screws applied new part replaced two screws

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Removed splash Guard to replace light bulb, reinstalled splash Guard. Installed new support clip.

This is a 1988 vintage microwave oven. I'm very relieved to have parts still available. The stirrer drive belt tore. I suspect dry rot, as I did this exact repair back in 2005.You simply remove the cover, replace the belt [easy] on top, and replace the blown fuse. While the oven cover is off blow out all accumulated dust and wipe/clean al ... Read more l areas that have a build up of dirt/crud. I purchased this microwave oven in 1988 and is very dependable.

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

Removed 5 screws on microwave trim and three additional screws on cabinet. Pulled microware part way out to expose broken drive belt on top and replaced with new one. Note: Microwave cabinet caught on connector in back of chasse and pulled it loose. Moderate difficulty in reaching back and reconnecting it. Otherwise an easy job that saved ... Read more $125 on service call and part was half the cost.

you will a security socket T20. this unit was installed over oven, remove trim cover,remove screws holding unit in place,I used a helper to get the unit out, once out you have to remove all the screws holding the cover on,on two of the corners they use a security hex screw so you need a special socket for that. remove the door latch switc ... Read more h,take your time or you will break tab holding switch in. ask me how I know.but super glued broke piece in place and plugged wire back in.the new latch may have a second pin but look at old one and plug wires in the same way.the light bulb does not screw out so I had to purchase the entire unit.total cost under a $100.00 to do repair.

Disconnected power and removed Microwave housing cover, observed burned end plastic connector of wire connecting to the thermostat (or thermal overload sensor); slightly wiggle one of the 2 wires to the thermostat would cause microwave power to cut out (when plugged in power). When powered on, I would try to run it but power cuts out aft ... Read more er just a few seconds. Removed the 2 wires from the old thermostat, removed the 2 screws that fasten down the thermostat, replaced with new thermostat and reapplied the 2 screws; cut off burned part of wire and resolder to new wire connector; reconnect both wires to new thermostat and reinstall MW housing cover. MW works good as new again. Thank you PartSelect!

It was a over the range microwave It had to be removed off the wall. Once down I removed the bottom plate and then removed the touch control panel. Per the instructions in the user manual tested the transformer it was ok. Next tested the capacitor it tested bad and also the diode tested bad. The parts were ordered from you. The parts inst ... Read more alled easily. Reassembled the microwave and tested. Unit no longed tripped the AC breaker and worked heating some water. Installed the unit back above the range.

You have to remove the cover which in my case was a little more difficult because the unit is wall mounted and has a frame around it. That was the hard part. Once the mounting frame was removed, you can remove the cover and the light bulb is on the top right side of the unit. One screw removes it and the new one pops right in. Put the cas ... Read more e back on reinstall it in the wall and voila...piece of cake.

Remove the housing cover which requires removing 7 screws that hold the cover on. The bulb and the pully's that the belt goes on are visible and the belt is easy to replace as is the bulb.

Pretty easy tear down and assembly once I removed it from cabinet (built in micro)