This door strike is an authentic OEM replacement part that is compatible with various models of top-load washing machines. The door strike is located along the door frame, where it engages with the latch when the door is closed. It keeps the door securely shut so that the washer can start and prevents it from swinging open while the washe...Read morer is running. It is a safety mechanism that prevents water leakage, injuries, and damage to the washer. If the door strike is damaged or worn down, it may be unable to lock the door properly and the washer may stop mid-cycle or fail to start altogether. Replace the door strike promptly to ensure the proper functioning of your washer.
This is an inlet valve for your washing machine. The inlet valve is an electrically controlled valve with a solenoid that opens and closes as needed, during the water filling cycle of the washing machine. This inlet valve features two inlets, one for hot and one for cold water, and three push-on valves that connect within your washing mac...Read morehine. If your washer is having issues filling or is leaking water from the area of the inlet valve, it needs to be replaced immediately. Replacing this valve will require a screwdriver and a wrench to replace. This inlet valve is an OEM part and is sold individually.
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is an 18 ml, or.6 fluid ounces, bottle of touch-up paint. It also features a brush for easy application. This quick-drying, long-lasting paint...Read more is perfect for fixing any nicks, scratches, or chips on the exterior of your appliance. This paint is white in color, and provides a durable finish.
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installation, you will need a flat head screw driver to replace the clamp and a drill to access the screws to remove the front of the washer. Be care...Read moreful if you do not have specific clamp pliers as the clamp could fly off. Once the front of the washer has been removed, take a quick look for water damage or any obvious signs of where the leak is coming from. If it is not obvious, run water to test.
This agitator assembly is an authentic OEM part that is compatible with various models of washing machines. It consists of a central shaft with a series of fins attached to it. When the washer is operating, the agitator rotates back and forth, causing the clothes to rub against each other and against the agitator itself, which helps to lo...Read moreosen dirt and stains. If the agitator does not move or moves erratically while the washer is running, then this is a sign that it is faulty. You may also hear unusual noises such as grinding or rattling and notice that your clothes are not distributed evenly around the agitator during the wash cycle.
This washer lid lock assembly is designed for top-load washing machines and ensures the lid remains securely closed during wash and spin cycles. It replaces worn or malfunctioning latches, helping prevent the machine from starting or pausing when the lid isn’t properly shut. The assembly includes the solenoid mechanism that engages the lo...Read moreck, contributing to safe and efficient operation. Compatible with a wide range of models, it’s an ideal solution for restoring reliable performance to your appliance.
This is an impact absorber, also known as a sound dampening pad, for washing machines. This sound dampening pad attaches to the top of your washing machine drum to reduce the severity and harshness of vibrations and movement during the washing and spinning cycle, to produce a quieter laundry experience. If your washer is shaking excessive...Read morely during operation, this pad may be worn out or simply missing, and in need of replacement. To replace this pad, you will need a screwdriver or wrench to access the inner portion of your washing machine and remove the old one and install the new one. This OEM pad measures 5-inches by 3-inches and is sold individually.
This clutch slider kit is genuine OEM replacement kit that fits in various models of washing machine. It is a part of the transmission system in your washer which is responsible for controlling the movement of the agitator during the wash and spin cycles. The assembly includes the clutch band, slider, and lock ring. The kit helps to regul...Read moreate the speed and direction of the agitator or drum. It allows the machine to start and stop spinning smoothly, as well as change speeds as needed during the wash and spin cycles. If the clutch slider kit has worn or damaged components, it can lead to problems like difficulty starting or stopping the machine, excessive noise during operation, or failure to spin properly.
Appliance spray paint is a great way to cover up any chips and scratches that have appeared on your appliances. Instead of replacing the part entirely, this is an easy fix. This is also a great way to give a fresh new look to any handles or areas that have discoloring due to wear. Make sure to clean the area before you begin and wear a pr...Read moreotective mask for safety. Give the can a good shake and spray a few inches away from the surface. Apply the paint until the area is fully covered as desired. Wait until the paint has dried before using the appliance.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
2
3
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Mike - For model number MVW7230HW0
December 6, 2022
Washer stopped after the extract cycle. I unplugged it for several minutes then plugged it back in and the screen is blank. The machine is completely dead. Please advise.
Hello Mike, thank you for contacting us. According to our research, the issue is likely with the UI panel, part number PS16221059. If replacing it does not help, we would recommend replacing the control board, part number PS12745529. It controls the whole functionality of the washer. Please reach out to customer service if you need help placing an order. Glad to be of help!
The Wash/Drain cycle ever completes, after the Power supply Failed & was replaced. Timer never times out & the drum spines at medium speed, till manually shut off.
Water drains OK.
Service tests & Cals run with no errors reported.
Thanks
Hello Kurt, thank you for getting in touch. It seems that the issue is most probably with the faulty user interface control board, part number PS16221059. We would recommend checking the board to fix the issue. We hope that helps!
What makes the tub shake while washing and spinning?
Hi Melvin, thank you for contacting us. Based on our research, the issue is most probably with the suspension rods. We would recommend replacing the suspension rod kit, part number PS12731247, to solve the problem. It supports the washer tub and keeps it stable. Glad to be of assistance!
How do I lift the top panel?
I have a new lid lock switch but can't figure out how to slide/lift the top panel so I can replace the lid lock.
Hi Philip,
Thank you for your question. We have included a link to one of our YouTube videos that you may reference on how to install the lid switch. The washer in the video may appear different from yours, but it will give you a general idea on how to install the part. If you have any questions, please let us know. We are open 7 days a week. We look forward to hearing from you!
Fabric softener remains in dispenser, not dispensed
Hello Joseph, Thank you for the question. In most cases this is caused by a clogged Dispenser. Soap can build up and prevent the water from entering the Dispenser to dispense the Fabric Softener. We hope this helps!
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Tab on door strike got broken off and washer would not operate without it.
44 of 55 peoplefound this instruction helpful.
John from AURORA, CO
Very Easy
Less than 15 mins
Pushed in on door strike and rotated it counterclockwise, removed broken strike and installed new strike. NOTE: when removing the old strike (turning counterclockwise) it felt like it might break and/or was attached with an screw that I didn't see but it came right out.
Was this helpful?
Thank you for voting!
Broken lid catch/strike
22 of 26 peoplefound this instruction helpful.
Brian from Cheney, WA
Very Easy
Less than 15 mins
Pliers
Rotate the broken piece counter clockwise in the socket in the lid to release it. Install the new one in a clockwise rotation.
Was this helpful?
Thank you for voting!
Faulty fill valve
18 of 22 peoplefound this instruction helpful.
Marian from GREYBULL, WY
Really Easy
30 - 60 mins
Nutdriver
Did troubleshooting after code LF showed on indicator window. Did troubleshooting; checked hoses for obstructions and small filters on inlets. All good. Ordered new fill valve. Came in a few days, good service. Removed control panel top by removing screws on back of control panel, then by pushing putty knife under each side to rele
... Read morease spring clips. Carefully lifted cover and set onto lid. Photographed fill valve at left side as you are standing in front of machine. Removed screws with small ratchet. Carefully removed wires via clips. Lifted out valve. Attached wires to new, set back into its place, replaced screws, tightened but not too tight so as to break part. Replaced control panel, pushing downward to engage spring clips, then replace screws on back. Re attached hoses, ensuring they were on the correct sides, plugged machine into power, ran through cycle and VIOLA!! Worked perfectly!! After a couple weeks, still working perfectly! Was VERY happy it was only fill valve and not mother board as the cost was a fraction. I found trouble shooting videos to be very helpful. Your service quite good.
My Orders
