MSX27HRAAD Hotpoint Refrigerator - Instructions

Reading other after action write-ups I diagnosed the problem to be either the defrost timer or defrost thermostat so I decided to replace both. The timer was hard to find. Turns out it was inside the kickplate grill which made it hard to demount and remount while maneuvering the wire connector around. Just took a few minutes longer tha ... Read more n expected. The thermostat was inside the freezer compartment requiring the refrig to be off and defrosted (heavy ice buildup on the coils confirmed diagnosis). Had to cut old thermostat wires and reattach new with crimp style wire nuts (provided with thermostat). Directions said to use silicone sealant in wire nuts - NOT provided. Need to attach new thermostat on top of coils with tie wrap (not provided). Overall reasonably easy with great results. Parts arrived very fast.

Removed 2 phillips head screws to remove ice maker (could have just loosened them)
Pulled fan off of shaft
Removed 2 phillips head screws on motor bracket , disconnected three motor wires & removed motor.
reversed process to install new motor & fan blade.
Space was a little tight for two hand and arms, but do-able.

There were not two screws as the instructions said. There was only one screw and I had to firmly pull it out after taking out the one screw. Then, to put the new one in, I had to line up two slots on two knob-like things and push it in firmly. Then screw the one screw in.

Other than the two-screw problem, it was easy.

For the past 6 months I've dreaded trying to find the parts and make the needed repairs to the slide rails. I just didn't have time to search for part numbers and drag all the tools out. I even contemplated buying a new frig. I thought I would have to find the original "Owners Manual". How stupid was I?

Within 15 minutes ... Read more the model number was determined and the parts (VERY EASY to find the exact part) were ordered. They arrived within a week (in a GE wrapper). I unscrewed two parts per rail and within minutes the repairs were done. It took me a lot longer to clean and wipe down everything to make the refrigerator look like new again. I bragged to all my friends (like I was some type of engineer) and have referred this website to many of them. What a fantastic experience. I saved over $1,200 and the hassle of moving a frig in and out of the house. Glad you're in business and on the web.

The replacement ice maker that GE supplies for my old refrigerator is a little different than the original. The electrical plug changed from a round plug to a square one. They include an adapter for it, but DON'T USE IT. There's not enough room for the bulky cord and connector. I got a much cleaner installation by taking apart the old and ... Read more the new ice maker, and then splicing in the old connector into the new ice maker. You need to carefully unscrew a circuit board inside to wire it in, and it'll be more secure if you solider 3 wires instead of using crimp connectors. The instructions also tell you to use your old 'ice breaker', but it won't fit on the new ice maker. I just left the new ice maker's ice breaker on, and it seems to work perfect.

Frig and freezer were defrosting and refreezing other than normal. Home warranty contractor told me ice maker was faulty. Purchased new ice maker. Unplugged frig, loosened 2 screws with nut driver. unplugged old ice maker, lifted old ice maker out. Took old fill cup off old unit and put on new unit since new fill cup was a different size. ... Read more Swapped ice maker insert from old to new unit. Plugged in new ice maker, slid over the 2 screws, tightened, and plugged in frig power. New ice maker works fine but still have defrosting and refreezing problem. Figure old ice maker probably works just fine. New contractor still trying to solve problem. Have had problems with this GE Monagram keeping proper temps since it was new in 2005, don't recommend it.

Unplugged refrigerator, removed three screws to take out part, disconnected the wires and removed bad unit. Removed fan blade from old unit and attached to the new unit. Attached wires, placed the new motor back in. Plugged it back in, within 20 minutes panel between freezer and refrigerator was cool to touch.

This problem had already occurred in 2008. Repairman replaced dual water valve. Cost $190.00. We decided to do it ourselves this time. The repairs were actually made in three phases. First, when I pulled the fridge out from the wall, unplugged it, and turned the water valve back on I discovered that the plastic tubing from water supply ... Read more into the fridge had long cracks in it and water was spraying out everywhere. I turned water off, went to Lowe's and bought the kit for that repair. Of course I didn't have to use all of the parts in the kit because the water supply was already there from the valve that came up through the floor. After turning the water back on and plugging the fridge back in, my husband and I tested it by trying the water dispenser. We found that water was leaking from somewhere inside the fridge, but didn't know where. After UNPLUGGING it, and turning the water off again, I took the metal back off at the bottom. It was leaking from the bigger plastic tubing (5/16"). It was just hanging, not connected into the dual water valve. Figured it had just broken. So I thought I just needed 5/16" tubing. I went on the GE website and it was very hard to get answers to my problem because I couldn't find the plastic tubing that it looked like. I ended up ordering the plastic tubing that goes up that back of the fridge to the icemaker. They sent me two of those, not one for the freezer and the bigger clear one (5/16") that I thought I needed. Then, I found this website! This PartSelect website is great!! After reading about other consumer repairs, I knew how to disconnect the dual water valve and found out that the smaller plastic tubing that goes up the back of the fridge to the icemaker had been pinched where it connects to the dual water value, barley hanging on. Just quick disconnected it from the valve by pushing up on the outside where the tubing comes out while pulling on the tubing. It came out, and I had to use needle nose pliers to pull some of it out where it had broken off inside. Then, pushed the new tubing into the valve and ran it up the back of the fridge, unscrewed the plate that goes over the clamp that holds the tubing, loosened the clamp a little, pulled the old tubing out, pushed the new tubing in, (the clamp was still tight enough) put the metal plate back on and replaced the screws. Then I re-connected the dual water valve to the electric clips, connected the 5/16" tubing to the right side of the valve. (The black tubing that goes up the back of the fridge goes into the left side of the valve.) put it back into place and screwed it back against the body of the fridge where it goes, put the back on and plugged it back in. We tested it again, and water was leaking, but not from where I made my first repair. I reversed everything again, and discovered that where the 5/16" tubing goes into the dual water value, it seemed more loose than it should have been. That is where the water was leaking from! I ordered the dual water valve, the 5/16" plastic tubing and the water tube union. I replaced the dual water valve-very easy! MAKE SURE YOU UNPLUG THE FRIDGE, turn the water supply off, disconnect the small tubing from the dual water valve, disconnect the electric connections to the valve, and reverse the process. What I did was replace the 5/16" tubing the comes out of valve & goes up into the storage tank behind crisper drawer. Used union there. Put everything back together and it works!!

First turned off power and removed top shelf.
Then I used a flathead to slowly pry the switch out by the two sides. You just anlge ita bit and it slideds out easily. Then I disconnected the wires from the old switch, connected the new one and installed the new switch by snapping it back into the cutout.

Shut off power to the refrige. Removed old icemaker, using large hammer. Installed new unit.

Look were timer was located, in my refigerator is next to the dial to ajust the temperature. used a screwdriver to get panel off. replaced timer then used a straight screwdriver to advance timer to turn on compessor . monitor temperature . checked out.

The icemaker's valve is easy to inspect and test. First, gently pull the refrigerator away from the wall, and unplug it. Turn off the water supply to the icemaker by closing the shut-off valve in the copper waterline leading to the valve. Use a screwdriver or nutdriver to remove the rear lower access panel from the refrigerator's back. ... Read more r />
Next, remove the fill tubing from the water valve. Use a wrench to loosen the flare nut on the brass fitting on the inlet side of the valve (above). Place a container or towel under the valve to catch the small amount of water that will spill from the valve and tubing.

Now use a screwdriver or a nutdriver to remove the screw holding the valve's mounting bracket to the refrigerator cabinet. Pull the valve out of the compartment and remove the tube (or tubes if both water dispenser & ice maker) on the valve's outlet. If plastic tubes don't come out with pliers and assuming there is enough extra tubing, then cut the plastic tubing with a even straight cut edge razor. Then, remove the solenoid's electrical contacts.

Push the plastic water and ice tubes int he appropriate holes in the new valve outlet, reconnect solenoids and remount new water valve.

Before installing the back panel on the refrigerator cabinet, test run the icemaker. Look for leaks, and tighten any leaky connections. If necessary, use Teflon tape or a similar product to ensure tight connections. Discard the first ice cubes that are produced because they are likely to have sediment in them.

Read less