MRS22WN Refrigerator - Instructions

had removed the doors to get fridge in thru small doorway when doors were reinstalled the elbow leak was replaced in about 15 minutes or less by cutting old elbow out of lines and the lines snap into new elbow with just a little force

removed water tray, used a razor blade to brake the seal from the face plate and the fridge, The hardest part was the three screws holding the dispenser face place on where rusted over. I wound up drilling them out. Once the screws removed, a slight lift, the face plate comes right off. I unplugged the cable, and set it aside. Now remove ... Read more the next three screws, and the dispenser falls forward, (as far as the water line allows) undo the screws leaving the one emplace to hold the ice lever. push up twist. The hard part is getting the new one up and in. just takes a little patients.

Remove the cardboard access cover at the bottom back of the fridge. On the left side, locate the run capacitor. Remove it by prying it loose from its socket, after first removing the wire hold down clamp. One wonders why the clamp is there, which makes it difficult to get the run capacitor out. Be careful not to disrupt in any way the cop ... Read more per refrigerant tubes. If you mess them up, you will have wasted your time and effort trying to repair the machine. I was lucky, since a failed run capacitor is the problem only about 12% of the time, based on what I’ve read. Hallelujah! It was the problem with my fridge.

Removed four screws at top and two at bottom and pulled ice maker unit out and replaced with the new lever .

Turn off power. Remove ice tray. Back out the two screws with nut driver and just lift ice maker off screws. Do not bend the water fill tube in the back . Now unplug the wire and remove ice maker .
To replace, match the color of wires on plug. Adjust wires in place and water fill tube and back on to the screws. Hold in place and snug ... Read more screws. Turn power back on. In 4 to 5 hours your ice will start .
FED-EX UT to MN was 13 days to deliver .

Simply detached the old ice container by removing four screws and removing one screw holding the lever onto the bottom of the container. A bit of advice; make sure you note how the spring is attached to the lever before removing the screw. It took me a bit to determine how the spring activated the lever when I was reattaching it to the ... Read more bottom of the container. Also, double check your order before you finalize it. I must have inadvertently hit the item twice so I received two of them. This resulted in me having to return one item and paying for extra shipping both ways. I received the part within two days of my order. It was a very fast turn-around. Also, when I realized that I received two parts and had to call to explain the situation, I found the person on the phone to be extremely helpful and courteous. She sent me information regarding how to return the product and didn't ridicule me once for my stupidity.

Looked it up on how to, follow the video
. Very easy 1-2-3 it was out and new one in..........??.

But I have back ground mechanical skills, I did see the video one time, and everything went smooth......

Looked up similar problems and found it to be the defrost timer. All I had to do was remove the plastic portion in the fridge section to get to the old timer. Popped the new one in and put it back together. Works great now. Would have been almost $150 to have a repair company come out and fix it.

i removed rhe old storage drawer from the refrigator. removed the front face and slid it on to the new drawer i received from Part Select. put the drawer into the refrigator and it fit perfectly. Part Select web site worked perfectly on selecting the right part. the part was delivered in three days. i would recommend this company for your ... Read more appliance replacement parts and would not hesitate ordering from them in the future.excellant service.

tony
scottsdale,arizona

take the ice bin out of freezer. there are 2- 1/4" screws. these screws only need to be loosened a few turns. the ice maker can be slightly lifted up and will come off the screws. unhook the wire harness. take the "L" bracket off the old ice maker and put on the new one. set the new ice maker in. hook up the wire harness. put the ... Read more new ice maker over the screws, tuck the wires out of the way and pull down into place. tighten the screws.

Removed outside cover on door despencer, (4 screws) unplug wire, removed unit from refrig and replace rusted thru wire that holds door shut. It was fairly easy. I actually took it apart twice, once for diagnosis and once for repair after the part arrived.

Unscrewed the gaskets from the doors and took off. screwed the screws and put tthe sealant on t he cornors on both doors and that was it. very easy. directions were great.

Downloaded a schematic of the ice container. Disassembled the ice container, keeping track of which different type of screws went where. Followed the schematic to ensure proper sequence of blades and spacers. Manually rotated unit prior to installing into the freezer in case of binding. Finished.

The repair was fast and easy .I removed the ice tray , disconnected the wiring connector and lossend two screws. I removed ice maker assy.and repeated in reverse order to install. I also installed a new water filter. I had ice in about 20 minutes.