MRS22WN Refrigerator - Instructions

Reviewed the video on your website and followed the directions to the letter. Great video

THERMOSTAT--First I removed the fours crews that hold the back of freezer (inside freezer) in place. I then pulled the thermostat out about 3 inches and disconnected the two wires. Plugged in the new one and put back in place. Replaced freezer back and installed the four screws that holds it in.(iIf your freezer has a ice maker just loose ... Read more n the 2 screws that hold it and lift the ice maker up off the screws
DEFROST TIMER--- removed one screw inside fridge by light bulb that holds in the timer and setting knob, then took out the two screws that held in the timer unplugged the old timer and replaced with the new one put back in the two screws that holds the timer in then replaced the one screw that holds the unit in place

1. Remove outer plastic face cover (4) screws.

2. Revove (1) U type nut keeper & (1) metal washer.

3. Remove (1) plastic nut on end of metal auger.

4. Remove inner plastic cover (4) screws and disconnect control rod. (Note postion of control rod befor disconnecting)

5. Note position an ... Read more d order of metal blades and plastic spacers on auger before siding off the end of auger to reposition them upon re-assembly.

6. Remove metal support panel from end of ice bucket (4) screws.

7. Remove auger & plastic cylinder from ice bucket.

8. Remove - slide drive blade off auger.

9. Drive blade replaced.

10. Re-assembled other items removed in reverse order

This was really simple, much like changing a light bulb. Two bolts loosened beneath the old unit to allow it to be lifted off and free. The power supply plug was easily disconnected. The new unit was then placed onto the loosened bolts, power supply reconnected and secured with the supplied wire tie. A small angled bracket was removed ... Read more from the old and reattached to the new as a support toward the from of the unit. The cycle adjuster was backed off a 1/2 turn as per the instructions....and the next morning....new automatic ice. Life is good!

Removed 4 screws holding face plate onto ice bucket. Removed the 3 screws holding the ice crusher housing. Noted postion and rotation of teh s;ring loaded ice selecting rod. Removed broken crusher housing. Reveresed process for installion. Took for test drive. Operational...

I checked the defrost timer (bottom front of the freezer / outside). I advanced it to send it into the defrost cycle. The heating elements in the freezer (behind the panel) did not heat up. I cut the wires going to the defrost thermostat. Turned the power back on, made sure the defrost timer was still in the defrost cycle and checked the ... Read more voltage at the wires to the defrost thermostat (before the heating elements). There was power / voltage there. I jumped out / bypassed the defrost thermostat turned the power back on and the heating elements came on. The problem was the defrost thermostat. So I replaced it with a new one from PartSelect.com. How it works...
When the defrost timer is advanced to the defrost cycle the switch closes sending power to the defrost thermostat. If the temperature is low enough, the defrost thermostat switch will close and sends power to the heating elements. When the temperature rises high enough about 55 degrees the switch at the thermostat will open and the heating elements will turn off (not allowing the freezer temperature to get too high, just enough to defrost the coil). The refrigerator will turn back on when the timer advances. The defrost timer will defrost every 8-12 hours.

At top of refrigerator compartment, took out screws to cover (where temp control is) and to the right took out 2 screws to remove defrost timer and installed in reverse order. In freezer compartment, unscrewed back of freezer wall and took off completely. Removed old freezer thermostat, the body of freezer thermostat snapped onto coil ... Read more and wire plugged in. Let run for 24 hrs, then made adjustments to temps, so far temps are back in normal range.

i removed the 4 screws holding cover. removed two screws holding timer. unplugged timer. plugged in new one. reassembled.

Loosen two screws, unclip electrical connection, remove ice maker, remove l shaped leveling piece of metal from old one, put on new one. Install in reverse order. Hint.. when loosening two screws, use a mirror

I had already removed the ice maker by loosening the two screws with a 1/4" nut driver, in order to compare the design and style to the intended replacement for size and critical measurements. The replacement was almost identical. The wiring harness was 2-3" longer than the original, but after snaping the wire plugs together I simply cur ... Read more ved the wire up and to the left to be out of the way. The hanging brackets are slotted and it was easiest to slip the back hanger over the head of the screw and let it slip down, then the front hanger was already to line up even though you can't see the screw with the ice maker in the way. I had to transfer an L-shaped metal bracket to the bottom side, matching the old assembly, and adjusting it to hold the bottom side away from the freezer compartment a little so it would hang level and secure. You have to snug the two screws with a screw driver or 1/4" nut driver by feel, since you can't see them with the icemaker in place. It took about 10 minutes to take out the old and another 10 to put in the new. We now have a full bin of ice, and the old plastic trays have been retired. I should have done this a year ago.

First, unplug the refrigerator since you're working with live wires.

Remove the 4 Philips sheet metal screws holding the plastic housing that holds the temperature control to the top of the refrigerator compartment. Pull the housing down then out since there is a tube on the housing where the water flows out the back of the re ... Read more frigerator during the defrost cycle.

Remove the 2 Philips screws holding the defrost timer on the plastic housing. Pull the connectors off the old timer and attach them in exactly the same positions on the new defrost timer.

Attach the new defrost timer to the plastic housing with the 2 screws.

Reinstall the plastic housing, making sure the water tube is inserted into the back of the refrigerator wall.

Plug the refrigerator back in and you're done.

pulled tank out and cut two plastic lines

The plastic slides on the Upper and Lower Drawers were broken from years of abuse sliding the drawers in and out. The replacement of the plastic drawers required removing the glass front pieces using a screwdriver and gently seperating the plastic drawer from the front panel from under the assembly. The front panel easily slide out within ... Read more the drawer runners. Simply slide the front on the new drawer and insert back into the refrig. That simple.

I ordered a defrost timer and defrost thermostat from partselect.com. Parts arrived in 2 days (earlier than expected). Unplugged appliance, removed bottom cover, unscrewed 2 screws holding timer in place, unplugged timer and replaced with new part. Fastened back into place. Next removed back cover of freezer (5 screws using nut driver ... Read more ). Disconnected old thermostat and removed. Wires already had connectors installed. cut off the connectors with some wire left on and reconnected them to the new thermostat with the included blue wire crimps. Tried to use the shrink tube to insulate but couldn't get it snug enough. Just used electrical tape instead. Reinstalled thermostat. Reassembled cover. Plugged in and fridge and freezer are working fine again. Thanks partselect.com.

unplug it, pulled compressor start relay,which i thing it was the problem, but i replace bolt, very easy.