My Orders
- Home
- MGS5870ADQ
- Instructions
MGS5870ADQ Maytag Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven wouldn't heat
1 person
found this instruction helpful.
-
Patricia from Buffalo, NY
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I removed the oven racks, the bottom of the stove and a v-shaped cover that was over the heating element. The old gas ignitor screwed off easily after I put W-D 40 on the nuts. I un ooked the old gas igniter and replaced it with the new one. The oven lit immediately after I replaced everything. I am very proud of my self, I feel like a
... Read more
femal Bob Villa. I almost bought a new range. Boy am I happy!
Read less
Was this helpful?
Thank you for voting!
Oven heated very slowly
1 person
found this instruction helpful.
-
Thomas from Muskego, WI
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Removed the drawer from under the stove then unscrewed the access panel in the back (two phillips head screws). Rather than take it off altogether I just swung it to one side.
The ignitor electrical connector required two hands to disconnect and it was a bit of a reach but came apart easily enough once I got hold of it.
... Read more r />Removed the racks and bottom from the oven. the bottom is held in by two pins in the back that you just slide toward the front then lift it out. I did not bother to remove the oven door, but some people might.
Then removed the two hex head screws holding the ignitor on and pulled the connector out of the hole leading to the bottom.
Installation is the reverse of removal The electrical connector was reluctant to back down the hole, but went with a little wiggling and pulling from underneath. Once you get it back down there the connector is keyed, so you can't get it wrong.
Piece of cake, really.
Total repair time: about 30 minutes, including the mandatory halfway beer break.
The ignitor electrical connector required two hands to disconnect and it was a bit of a reach but came apart easily enough once I got hold of it.
... Read more r />Removed the racks and bottom from the oven. the bottom is held in by two pins in the back that you just slide toward the front then lift it out. I did not bother to remove the oven door, but some people might.
Then removed the two hex head screws holding the ignitor on and pulled the connector out of the hole leading to the bottom.
Installation is the reverse of removal The electrical connector was reluctant to back down the hole, but went with a little wiggling and pulling from underneath. Once you get it back down there the connector is keyed, so you can't get it wrong.
Piece of cake, really.
Total repair time: about 30 minutes, including the mandatory halfway beer break.
Read less
Was this helpful?
Thank you for voting!
Oven shutting off, getting an F1 error on ECM
2 of 4 people
found this instruction helpful.
-
Ben from Belen, NM
- Really Easy
- 15 - 30 mins
-
Screw drivers
Remove rear sheet metal cover. Disconnect the temp sensor wiring connector (on the left side as viewed from front).
Open oven, take out the 2 screws attaching sensor and remove. Reverse for installation.
Included wiring adapters are not needed for this model oven.
Open oven, take out the 2 screws attaching sensor and remove. Reverse for installation.
Included wiring adapters are not needed for this model oven.
Was this helpful?
Thank you for voting!
Oven Wouldn't Heat
1 person
found this instruction helpful.
-
JANIE from DETROIT, MI
- Really Easy
- 1- 2 hours
-
Pliers, Screw drivers
I first removed the screws inside the oven,let the tube that the flames come out of hang down,removed the screws from the igniter. Then I took the cover off the back of the stove and unplugged the old igniter and plugged in the new one. I put all screws back and put every thing back in place and the oven has been heating up every since
... Read more
. Thank you parts select. My husband is a otr trucker and won't be home until the 20th of this month. One less item on his "honey do list".
Read less
Was this helpful?
Thank you for voting!
Oven wouldn't heat, broiler would.
2 of 4 people
found this instruction helpful.
-
Pati from Marietta, GA
- Really Easy
- 1- 2 hours
-
Pliers, Screw drivers, Socket set
Removed all screws from back panel of stove, disconnected all electrical, shut off gas. Removed valve and replaced with new. Put all back together. Turned on gas and checked for leaks. Success!!
Was this helpful?
Thank you for voting!
Igniter on burner
1 person
found this instruction helpful.
-
daniel from MENIFEE, CA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Firmly grasp burner turn counter clockwise while lifting. Photograph the location of the wires. Remove with a Phillips head screwdriver. The igniter will lift and turn one quarter turn then pull through bottom. Reverse the steps to install the new igniter. Test knew igniter. Put tools away
Other Parts Used:
Was this helpful?
Thank you for voting!
Oven would not maintain temperature and not heat up correctly
1 person
found this instruction helpful.
-
Kevin from EDGEWOOD, NM
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Unplugged the Rang. Removed the oven door. Removed the lower cover for the Bottom heater. Removed the two screws that held the igniter to the burner. Went to back of oven to disconnect the igniter. removed the old igniter. Installed the new Igniter in the reverse order.
Was this helpful?
Thank you for voting!
Oven wouldn't light.
1 person
found this instruction helpful.
-
Andy from NEDERLAND, CO
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
It's happened before and the igniter has always been the problem. This time, however, the mounting holes were slightly off and had to be drilled out. The connector didn't mate up and so both had to be cut off, the wire stripped back and wire nuts used to make the connection. In the end, it all worked out. I guess since its kind of old, yo
... Read more
u can't stock every component for every oven. Oven works perfectly now.
Read less
Was this helpful?
Thank you for voting!
Broken Inner Glass Pane
3 of 7 people
found this instruction helpful.
-
Joseph from Lewiston, ID
- Easy
- 30 - 60 mins
-
Screw drivers
I received my glass panel realy quick from Part Select. It was an eansy job to install the new pane.
It took less than an hour. Thanks for Your prompt service.
It took less than an hour. Thanks for Your prompt service.
Was this helpful?
Thank you for voting!
Oven took to long to preheat
1 person
found this instruction helpful.
-
keith from westfield, MA
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
I expected to see a thermocouple and a heating element next to the gas valve but after reviewing other PartSelect stories from people with a similar problem I realized that the heating element also serves as the switch. Apparently as the heating element is energized by the oven control it draws more amps. The gas valve is allowed to open
... Read more
at a specific level corresponding to a sufficiently glowing heating element. I ordered a new heating element. The part received was made up of two pieces. The heating element and the metal mounting bracket. The element was identical but assumingly due to the age of my stove the bracket was slightly different. Fortunatly I was able to slide the new element into the old bracket. The only other obsticle was that the new element came with a two conductor connector and the old was installed with ceramic wire nuts. The connector was cut off and the ceramic wire nuts were reused. Its working fine.
Read less
Was this helpful?
Thank you for voting!
Oven would not heat
2 of 4 people
found this instruction helpful.
-
BEVERLY from SELIGMAN, AZ
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
Husband did repair. He removed the
the ignitor. Was a little difficult to remove. I couldn't tell you what he did and in what order.
the ignitor. Was a little difficult to remove. I couldn't tell you what he did and in what order.
Was this helpful?
Thank you for voting!
My original back leg broke because the floor is uneven. Had to pull it out several times.
1 person
found this instruction helpful.
-
Phyllis from BROWNVILLE, NY
- Really Easy
- Less than 15 mins
-
Wrench (Adjustable)
Put the back of stove on blocks of wood to get high enough to screw the new leg in.
Was this helpful?
Thank you for voting!
Broiler wouldn't turn on(ignite)
1 person
found this instruction helpful.
-
James from FLORISSANT, MO
- Very Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Ordered the broiler igniter that matched my model from part select and installed. Easy and part works as it should. Only took a few days to get here and saved me $40 by not purchasing at a local parts store as well. Will use part select if there are any future needs.
Was this helpful?
Thank you for voting!
The oven did not heat, but the top burners worked fine.
1 person
found this instruction helpful.
-
Marvin from DECATUR, GA
- Really Easy
- 15 - 30 mins
-
Screw drivers
1. Slowly pull the stove from wall. 2. Unplug 120 volts plug from outlet. 3.Turned off the gas outlet. 4. Open the stove door, remove the racks, then unscrew (2) screws that hold the short oven sensor in place. 5. Slowly pull sensor out of it's housing. Remove the clip that holds the sensor. Install new sensor using the clip. Push sensor
... Read more
back through the hole opening. Screw the (2) screws into the mount to secure the sensor. 6. Plug the 120 volt plug into the wall outlet. Turn on the gas outlet. Test stove by turning on oven. It works like a new stove. Wife is happy, and Thanks Giving Dinner is on! Reverse your steps to secure your stove. A total of 25 minutes after cleaning the dust under stove. Thanks for everything. By the way, Thanks Giving Dinner was delicious.
Read less
Was this helpful?
Thank you for voting!
gas burner on stove top not lighting ,other 3 work fine.
1 person
found this instruction helpful.
-
Philip from Santa Maria, CA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Make sure all burners on stove top are off.Half twist burner top to separate burner from stove top.The burner slide fits over the metal tube that transports the gas to the burner.Remove the 2 slip fit connected wires from the underside of the burner.They should be of different sizes so no worries about incorrectly re-attaching them.The ig
... Read more
niter has 2 philips screws holding the igniter to the burner, Remove those and the igniter will be able to be removed with a little wiggling.Insert new igniter thru the hole in the burner and secure with the 2 screws. Reattach wires , place burner back on top making sure the wires aren't being crimped when the burner slides over the aforementioned metal tube and twist burner to seat in stove top, turn on burner to confirm igniter now ignites properly.
Read less
Was this helpful?
Thank you for voting!