MES5770ACW Maytag Range - Instructions

First of all, I shut off the electricity to the stove.

I had to remove the two screws holding the stovetop in place. I then lifted it up and braced it to keep it from falling, removed the bad element, carefully marking the 4 wires that were connected to the element. I then disconnected the wires, and removed the two bracket ... Read more s holding the element in place. I replaced it with the new element, reconnected the wires, returned the stovetop to it's original place, put the two stovetop screws in, and turned on the electricity. Then I turned on the element, and it works just fine.

I ordered the part one afternoon. It arrived before noon the next day. Then I simply removed the old seal (with about 2 dozen spring clips). Inserted the new part by carefully inserting the new seal into its corresponding hole at each end and then worked my way around the seal while inserting each attached spring clip into its correspon ... Read more ding hole.

Removed stove top. Removed old element paying attention to wiring connections. Installed new element. Redconnected wiring. Put stove top back in place. Tested. Ate dinner.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires to remove the old sensor. Went on line to find out where to order it from. Ordered it, It was on back order but was only about 1 week to receive. Reversed the procedure. WA LA. It works great.

My wife called a service company and was told that a tech would have to inspect the stove.
service charge 60.00 After inspection the parts would be orderd and a 200 fee for labor plus the parts would be charged at the completeion of the job. 2 weeks for part. I found you on the net orderd the glass. got it in 2 days and I completed t ... Read more he repair in 20 mins. Cost 89.00

very very easy. but keep in mind that step one, killing the power at the power box. I jumped that one to a near disastours outcome, thankully all turned out well byt there was a hell of bang and VERY bright flash. Still was worth "doing it yourself" just keep in mine the cut power side...Safety first!!!

It wasn't the handle that was broken, it was what the handle was attached to that was. I removed the door by opening to first detent and just lifting the door upward. Once off, I removed the screws on the top sides and underneath - a total of 9. This allowed me to remove the edging on the sides and underneath - the front glass came wit ... Read more h it as well. Then I removed the Top trim by removing a screw on each of the sides and two on the front - this was the piece that was broken. Since I had already disassembled most of the door, I went ahead and dismatled the rest so that I could clean everything. The pieces that would fit went into the dishwaser and the rest (including the glass) I washed by hand (except the white insulation pieces of course). I did take apart the double glass panel by lifting up on a bent tab on one of the corners - this allowed me to clean the insides as well as the groves in which the glass sat. After everything was clean, I reassembled everything in the reverse order substituting the new trim for the old.

Notes: The top of the trim piece has two diferent screws - two short ones that screws into the trim piece itself and two that go through to the door metal. The screw that I ordered ended up being one of the short ones and I wanted the other. The snap nut was correct, and was what the longer screw to the trim actually grabs on to. I ended up using one of my own screws that fit like a dream, but wasn't painted white. The other note is that the sheet metal that the trim piece screws into from the front was slightly stripped. All I had to do was to place the metal on a hard surface and hit the holes with a hammer to bring them back into a usable form - not ideal, but worked nonetheless.

Turned the circuit breaker to "off"
Unbolted the unit from its cabinet (4 screws - visible when the oven doors are open - secured the unit in its cabinet)
Slid the unit out of the wall about 2 inches
Removed the control panel.
Unbolted the cooling fan assembly
Unplugged the assembly from the wiring harness
Re ... Read more moved the cooling fan from the oven

Plugged in the new cooling fan
Bolted the new fan in place
Replaced the control panel
Slid the unit back into position
Bolted the unit in place
Turned the circuit breaker back on
Tested

No problems - the hardest part was having to reach to the back of the oven from the front.

As the video described I just unscrewed the sensor from inside the oven. Although I couldn't pull the wiring harness through the insulation (the wires were gathered in back with a wire tie) just four screws to loosen the back panel for access to the connection. My wife says it seems to be heating perfectly now.

Removed the two screws holding the element in place. I then pulled the element and wiring out until I saw the connecter. I disconnected the two wires and then chose the correct connector from the package, snapped it back into place, put the screws back, turned on the breaker then tested the oven and found that everything was working corre ... Read more ctly.
This is the second time I have ordered from Part Select, the first time was for a front LED panel on the same appliance. With the help finding the part you need and the comments from other customers I have saved a lot of money by repairing these problems myself. Oh, and the best part is the look on my husband's face when he came home and found out the repairs were made by me and not a repairman that he said I should call. He said he would laugh when the first repair by me didn't work but who's laughing now : )

removed the screws,pulled the element out about 3 inches disconnected the 2 wires

Used cooktop creme, oven cleaner and Mr. Clean sponges. After many days of working on the surface, we were able to remove 99% of the sauce.

I removed the door from the oven and set it on towel on the table, and started the repair of the door. I removed the screws one at a time, and one layer at a time. Becareful you need to take the whole door apart, and remember how it goes bact together. In the end it was worth it. The hardest part was getting the right part. I thought I ... Read more could order the whole door, and found out after several calls they don't sell the whole door. Part Select both times I put in my order had the parts at my door within 2 to 3 days. I also had to return one of the parts and within 2 to 3 days the part was credited to my account

I was told by appliance repairman that sensor and electronic panel were out - so ordered both as PartSelect was less expensive (about 1/2) than service call price. Sensor was in stock and arrived in 2 days, panel was special order from factory.
Replaced the sensor. Pressed Control Lock pad for several seconds and oven clock came on ... Read more . Was able to set baking temp, broiler, and convection operation as normal.
Canceled order on panel as Sensor fixed my problem.

Turn off breaker.
Remove knob, pulls off. Pulled stove away from wall.
Removed front panel with switches attached.
There are screws in front and back.
Removed screws that hold switch in place.
Transferred wires one at at time to get proper location.
Reverse process for reassembly
Gary in Ohio