MERH865RAS13 Maytag Range - Instructions

Pull out the range...hardest part.
Remove back panel.
Remove/install switch
PS,
This is second switch I had to replace. Try making them in the United States.

Removed old assembly, attached wires to new and inserted into space for same. Of course you must turn off the range circuit breaker. The part that took the most time was removing the old assembly. Once that was done, the rest took only a few minutes.

Went to this site and read what a few others had done to fix their problem. Found the model number and ordered part. It was on our steps in less than 3 days. It took less than half an hour to replace and put back together. Just had my first meal from "NEW" oven. Great site, great price and great service!


Thanks!

Remove lower drawer.
There are five screws along the bottom bracket of the oven door. Remove the outer two screws, and loosen the one in the middle almost all the way out. The other two screws can stay tight (at least on my model). Clean the new glass before you insert it. Slide the new glass into the upper bracket and center it. Wig ... Read more gle the lower bracket onto the glass and tighten the center screw, keeping the glass centered. Install the other two screws and you are done.

Turn off breaker to oven and verify no power.
Remove the two screws holding metal panel covering baking element on the floor of the oven (near back of inside of oven)
Remove two screws holding element mount to floor of oven (near front of inside of oven).
Remove single screw holding element to back wall of oven.
Pull ... Read more element toward front of oven, carefully holding wires so they do not disconnect from element and slip inside the ovenback wall.
When you can reach the wire connections, hold each one with a pair of pliers and disconnect from element ends.
Connect new element ends into wire connections. Be sure to insert all the way into both connectors.
Carefully, push the wires back into the rear of the oven, trying not to scrape the wires on the sheet metal.
When fully inserted, reinstall single screw to secure element to back wall.
Re-install two screws to element mounting at the front of the oven floor.
Re-install two screws to secure element cover plate to the floor of the oven.
Turn on breaker for oven and verify oven has power.
Turn on oven to bake at 400 degrees.
Wait for oven to come up to temp and maintain for 10-15 min (you may smell some burning smells as the element heats up the first time).
Enjoy...

First I removed the two wires from the back of the stove. I then removed the two screws that were holding the element in place. Installed the new one without problems

It was easy to remove the old oven door gasket. Just a little tug was all that was needed. Installing new gasket was just as simple as tucking in the gasket end into the hole at the bottom and pushing the clip in the corresponding hole.
TIP: roll the end of the gasket and feed into the hole then use a small tipped screw driver or t ... Read more he point of a needle nose plier to finish installing the ends into the hole at the bottom of the door opening.

I took the back panel off, removed the old lens, installed the new lens. How easy to order from home, receive the part, do the repair and pay less than it costs to simply drive to the parts house. Cool....

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Spoke to your very helpful staff, who advised me that a likely problem was the oven sensor. I took a chance and ordered the part, which came promptly. Your service video for the part was most helpful in my decision to try the part. Installation was a breeze, but it was the oven controller board that had failed and not the oven sensor. ... Read more That called for a service professional, who ultimately fixed the problem. Your service though, was excellent and I would highly recommend you to others.

I switched the oven sensor easily enough, but it did not remedy the problem, so we are in the process of replacing the oven since it's about 20 yrs. old.

Element was sent by buyer, As they recommended, when model of stove given to them. It was upper right rear. When element came. First took off old element. ...Match both element , new element did not look exactly the same, small variation. It did not come on.. I moved old element from left side to right side . Old element worked on both si ... Read more de .. tried new element on left side also.. still didn't work.. so I called right away and explained.. new element did not work.. not defective, but, just wasn't the right one.. I had a specialist came and check it out also. I was told wrong element.

First I called a repairman and left a message. That was 3 weeks ago. So, I 'googled' the error message and determined what part I thought I needed. Ordered the part on Wednesday evening and it was there when I got home from work on Friday. I unpacked the part, got a phillips screwdriver and then watched the repair video on your websit ... Read more e. About 20 minutes later I pushed my stove back in place and the flashing said 'set time'. Then I checked both ovens, and have since used both, and everything works!!

Watch the video. Spot on instructions. Easy peasy.

Door was removed very easily. Outside trim pieces were removed. The rest came apart like a simple puzzle. Inside glass is very easily accessed. Upon assembling, time was well under an hour. Shipping was fantastic and I saved close to 200dollars between a service call and a repair.