MER8772WS0 Maytag Range - Instructions

Took off top and pulled out old element and plugged in the new one

Repair was very simple. Took the door apart in layers, replaced the glass and put everything else back. it took longer to clean the stove than it did to actually take it apart and put it back together. guess i didnt need to be that much of a clean freak!

I took the oven door apart, pulled out the broken fragments of glass and replaced it with the new glass. I should have taken notes as I took the door apart because it was a bit tricky to remember how all the pieces fit back together.

I was very impressed with how quickly the parts were shipped and the quality of the packing ma ... Read more terials to protect the glass as it was shipped.

Purchased new bake element from PartsSelect. Very easy to install, unplug range, remove 6 screws, slide element out and unplug end, remove old element. Reverse procedure to install new element. My range was about 6 years old and in excellent condition, was considering buying a new range. Found PartsSelect on-line and ordered new element. ... Read more Their website is very easy to use and find correct parts.
Saved lots of dollars, this PartsSelect website and service is great.

Following your installation, the old part came out easily, with new part installing easily., oven heat is being regulated properly..with range pulled out for part replacement, got that area cleaned too

the hardest part was moving stove to trplace part

Took the old levelling leg out and screw the new one in.

It was really easy, just lift the door off from the range, I set it down on the box that the hinges came in, took the six screws out to release the front fascia of the door from the back, hinges are right there, un-screw and install the new hinges, put everything back together in reverse and lift the door back on to the range, less than 1 ... Read more 0 minutes!

pulled the old gasket, the new one fitted perfectly. No effort at all.
An instruction sheet would be a bonus. I wish you put instruction sheet in all parts OR a web link for video instructions. a web link would be great

I watched the video you provide and it answered all my questions. You estimate repair at 10 minutes. My wife said I waz done in under 10 minutes Watch the video, it explained every step and all the little tricks to the snap connections.

I watched the repair video on this site and another on YouTube before I started. The rear panel has a different shape and two additional screws on the bottom edge. The power clip was easy to manipulate.
This was an easy fix for a seventy year-old like me!

Very easy. Pulled the stove away from the wall. Used a screw driver to remove the two nuts to release the heat sensor, disconnected the wire, removed the sensor. Inserted the new sensor, plugged back into the circuit. put the two nuts back.
Beware, if the first time you put the oven on, if the error message comes back up (mine did ... Read more ) push the cancel/off button, wait a few minutes, put oven back on. System probably needed to reset. Mine worked perfectly after.

1993 model oven, built in wall model, so didn't to remove oven for the normal rear access to replace the lamp socket. As someone else posted, replacement can be done from inside the oven -- BUT the socket removal was more complex than just 'twisting it out.' But below worked! (1) Turned off oven power at circuit breaker panel. To facilit ... Read more ate working in the oven compartment, removed oven door (2 screws on back of door), raised the over door almost closed, put 2 large nails through the hinge holes when they lined up. Lifted the door out (heavy ~20-25 lbs) and put aside. (2) Put work light inside oven. (3) unscrew glass socket lens and the bulb). (3) Using inspection mirror, studied the inside of the socket to determine that its lock tab type and locations -> were on left and right sides of the socket. These tabs needed to be bent in, but they were each held out by a small circumferential length of think metal, a tab about 3/16" x 3/8". These small tabs could be moved/positioned by just finger friction, with a little start with a screwdriver tip on their edge! I got an end positioned to put sharp screwdriver under that end, then pried it (bent it) inward a short distance. Enough to use needle-nosed pliers to pull it completely out - came fairly easily. Repeated on other side of socket. (4) Then, with pliers, bent each of the 4 locking tabs inward a short distance, Used sharp tool to get one socket edge lifted a small amount; then use mini-pry bar and screwdriver to gently pry around the socket in steps, working evenly around its edge. At about 3/8", it was free. Lifted it inward gently so as not to damage the insulation of the 2 wires attached to its rear. Noted the direction of the wire tabs was straight up (keep same orientation on new socket). (5) Needle-nosed pliers on each connector to gently work the connectors off their socket tabs. Note one tab is larger than the other. Keep the wires inside the oven compartment. Don't damage the insulation. (6) Pushed the wire connectors onto their respective new socket tabs. Aligned socket with the tabs upward, and inserted it, careful to nurse the wires back into the oven wall hole; press socket into the hole, pushing it in evenly and firmly until flush. (7) Pushed in the new type bulb that came with new Socket. Turned on power, and light came on. (8) screwed on new glass cover. (9) Lifted oven back onto the hinge prongs. (easier with two people to get the prongs aligned and into their door slots.) Worked door left and right to get it to lower down fully. Removed nails, lowered door, and put its 2 screws back on. (10) Poured a glass of wine.

After removing element cover off with Phillips screw driver, found a little screw in bottom of oven. Couldn't find where that came from. Removed two screws from element bracket from floor of oven and one holding in the back wall. Most difficult was pulling the old element out of the electrical clamps and hoping the wire would not pop bac ... Read more k into the insulation/ and replacing with the new bracket. That is where my hemostat came handy as pliers were too big and the hemostats stabilized the connection without it popping back into the oven. What was really astonishing was the new element and floor bracket DID NOT line up with the screw holes in the bottom of the oven. Could not adjust/move bracket as some of the element was "clawed?" on the bracket and feared I would damage it. Thus I now have two extra screws along with the one found on floor of the oven. Replaced cover and it currently heats nicely.

Remove the door, remove screws from all sides

Remove sides and face of oven door by sliding down from under the oven handle trim.

Remove screws on 2nd light of glass and set aside.

Now you are at the inner door panes. their should be two in an insulated type unit.

Remove the remaining screws ... Read more from the handle pracket and the permiter frame for the glass/insulation. Remove permiter frame and set aside.

Pull out inner door glass frame. get a pair of pliers and bend tab on frame up so you can pull the frame sightly apart, replace the glass, secure frame tightly around glass slide tab back into reciever slot and bend down ( you may need another person to assist in keeping both lights in the frame while trying to ben tab back in to place)

reassemble door as it came apart carefull not to over tighten the screws, they strip easy.