My Orders
- Home
- MER8770WS0
- Instructions
MER8770WS0 Maytag Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Bake Element burn out
1 of 2 people
found this instruction helpful.
-
Bob from Oroville, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
Can of Corn fix! Remove the two screws in the element cover plate (they're in the back- left/right corners). Remove the two screws that hold the element in place. Pull out the two prong ends of the plug in portion and hold the black / white leads so they do not fall back in behind the unit. Plug in new element (it only goes one way). Scre
... Read more
w everything in and test. Place cover plate on after test. Like I said ... a "Can of Corn" fix!
Read less
Was this helpful?
Thank you for voting!
cleaner
2 of 5 people
found this instruction helpful.
-
Mary from Duarte, CA
- Really Easy
- Less than 15 mins
just needed clearner for the top of my glass top, the operator was very helpful I received my clearniner in 7 days thank you
Was this helpful?
Thank you for voting!
Terminal block arc'ed because a wire had become loose.
1 of 2 people
found this instruction helpful.
-
Larry from Scranton, KS
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All ch
... Read more
ecked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.
Read less
Was this helpful?
Thank you for voting!
Needed to replace over door gasket
2 of 5 people
found this instruction helpful.
-
Genie from Conshohocken, PA
- Really Easy
- Less than 15 mins
-
Pliers
Very Simple, I recommend pulling the old gasket in sections, and popping the new gasket metal holders in the holes as you go. You can't mess it up. For the ends, I tucked them in using a pair of needle nose pliers, but any small slender tool, such as a thin screwdriver, will work.
Was this helpful?
Thank you for voting!
Bake element fried
1 of 3 people
found this instruction helpful.
-
Roy from Stallings, NC
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
I turned the braker off the electric range and removed the bottom plate that housed the bake element (two screws had to be removed). There were three screws that held the bake element in place. I pulled the bake element from the two electrical prongs that connected to the oven. I replaced the element and put everything back in place.
... Read more
r />
More importantly than all of the above. I received the part from Partselect in two days. When I originally put the eleemnt in its place it did not work. I called partselect and was issued another element in two days. The people I spoke to on the phone were proffessional and sympathetic to my problem. I will definetly recommend this company to other people. Thank you very much....
More importantly than all of the above. I received the part from Partselect in two days. When I originally put the eleemnt in its place it did not work. I called partselect and was issued another element in two days. The people I spoke to on the phone were proffessional and sympathetic to my problem. I will definetly recommend this company to other people. Thank you very much....
Read less
Was this helpful?
Thank you for voting!
oven not heating above 325 deg.
1 of 3 people
found this instruction helpful.
-
maciej from Pensacola, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
remove stove , unplug power , took back panel off, disconnected wiring to the heating element, from the inside of the stove removed bottom plate /two screws/, removed heating element /two screws/. installed new element .put other parts in order they were removed
Was this helpful?
Thank you for voting!
Oven would not heat but broil element worked fine
1 of 3 people
found this instruction helpful.
-
Detlef from Merritt Island, FL
- Really Easy
- 15 - 30 mins
-
Screw drivers
The Maytag stove has a hidden element and therefore I had to remove the bottom cover to expose the element. I had to remove the three screws that held the element in place. The element was badly bent out of shape and must have been that way since new. It was difficult to remove the element and I had to pull the stove out to access the e
... Read more
lectrical connection in the back to disconnect it. The replacement part was a perfect fit and the installation of the new part went with out hitch and the oven works perfectly.
Read less
Was this helpful?
Thank you for voting!
replaced faulty door hinge and installed tip-over bracket to floor
7 of 21 people
found this instruction helpful.
-
Rodney from Knoxville, TN
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
removed door (no tools required - just lift and pull door out of range). removed front door panel with a screwdriver. removed/replaced door hinge with nutdriver. replaced front door panel with screwdriver. replaced door on range (again, no tools required). then installed tip-over bracket to floor/wall behind range. measured location, dr
... Read more
illed pilot holes and installed wood screws into the floor and rear wall stud.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
burned oven bulb
3 of 9 people
found this instruction helpful.
-
Ivanka from Atlantra, GA
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new ligh
... Read more
t bulb in was not the problem.
Read less
Was this helpful?
Thank you for voting!
oven light not working
2 of 6 people
found this instruction helpful.
-
Richard from Gaylord, MI
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers
replaced light socket but did not repair problem. must have burned the motherboard.
pleased with service from your company.
pleased with service from your company.
Was this helpful?
Thank you for voting!
Inside Light would not work
2 of 7 people
found this instruction helpful.
-
Dan from Caddo Mills, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver
Turned off CB for the oven,Remove the oven from the cabinet , remove the back of the oven, replaced the light Assembly. turned on CB for the oven, tested the light. and truned off the CB and replace the back and reinstalled the oven in the cabinet.
Was this helpful?
Thank you for voting!
Switch had burned out due to faulty wiring by electrician when appliance first installed
1 of 4 people
found this instruction helpful.
-
Doriss from Cartersville, VA
- Really Easy
- Less than 15 mins
-
Screw drivers
my son simply replaced the switch, so now I have a working oven light once again
Was this helpful?
Thank you for voting!
Heating element not working
0 of 1 people
found this instruction helpful.
-
Renee from Charlton city, MA
- Really Easy
- Less than 15 mins
-
Screw drivers
Ordered the part late Wednesday night and paid for standard shipping. The part arrived Saturday morning, we removed the old part and screwed in the new one. It took minutes! We were shocked at how inexpensive the part was, how user friendly this site is and how quick the order arrived. We will def use this site again!
Was this helpful?
Thank you for voting!
replaced oven lightbulb
0 of 1 people
found this instruction helpful.
-
peggy ann from forest city, NC
- Really Easy
- Less than 15 mins
very easy
Was this helpful?
Thank you for voting!
oven light burnt out
3 of 10 people
found this instruction helpful.
-
William from Schwenksville, PA
- Easy
- Less than 15 mins
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
Was this helpful?
Thank you for voting!