All Installation Instructions for Kelvinator Range MEF302PBDB

My burners were shot!

2 of 3 people found this instruction helpful.

Karen from POPLARVILLE, MS
Very Easy
Less than 15 mins

Pulled out the old, and replaced. Very simple for a 62 year old woman! I cook a lot, being from the country, and Imwas so excited to get my burners fixed! Should have done it years ago! Thanks!

Other Parts Used:

Surface Element - 6 Inch

Surface Element - 8 Inch - 220V

Was this helpful?

Needed an additional rack

1 person found this instruction helpful.

Gary from Darragh, PA
Really Easy
Less than 15 mins

Open the door and slide in the new rack.

Was this helpful?

replacement

1 person found this instruction helpful.

Georgiana O from E MONTPELIER, VT
Really Easy
Less than 15 mins

remove old, set in new

Other Parts Used:

Surface Element - 8 Inch - 220V

6" FM CHROME DRIP B

Was this helpful?

Burner would cutoff intermittently

1 person found this instruction helpful.

Joseph from FREDERICKSBRG, VA
Very Easy
Less than 15 mins

Pulled out old burner/inserted new

Was this helpful?

Old bowls were rusted beyond ability to clean

1 person found this instruction helpful.

Shelley from CLYDE, TX
Very Easy
Less than 15 mins

Put the new bowls under the stove top burners with disposable liners to protect them. They look very clean and shiny now!

Other Parts Used:

6" FM CHROME DRIP B

Drip Bowl - 8"

Was this helpful?

Terminal block was bad.

1 person found this instruction helpful.

Chuck from EVANSVILLE, IN
Very Easy
Less than 15 mins
Screw drivers

Cut the old block off tied new wires to hot wires . That easy!

Was this helpful?

Left an appliance on surface element and melted paint onto the element

1 person found this instruction helpful.

Kenneth from LANOKA HARBOR, NJ
Very Easy
Less than 15 mins

Plug the new element into the space on stove

Was this helpful?

Baker Element burned out

1 person found this instruction helpful.

James from Navarre, FL
Really Easy
Less than 15 mins
Screw drivers

Really easy process. First I unplugged the oven for safety then I proceeded to remove the 2 screws that were holding the old element in place. Next I removed the old element then installed the new one. After installing the two screws I connect the oven back to its power source and BANG!............. It works like a charm

I g ... Read more

Read less

Was this helpful?

The bake element burned out

1 person found this instruction helpful.

Kenneth from Lake Luzerne, NY
Really Easy
Less than 15 mins
Screw drivers

I turned off the circuit breaker to the range. Next I removed the two screws that fastened the element to the rear of the oven. Then I pulled the element out far enough to be able to reach the spade clips and disconnected the element. I connected the replacement element to the clips and fastened it to the rear of the oven with the two scr ... Read more

Read less

Was this helpful?

Baking element went out

2 of 4 people found this instruction helpful.

Brandon from Lexington, NC
Really Easy
Less than 15 mins
Screw drivers

Removed back cover, unhooked wires, unscrewed and removed bad baking element. Reverse order to install. Less than 15 min. repair job.

Was this helpful?

Oven element burned out

1 person found this instruction helpful.

Dr. Johanna V. from North Conway, NH
Really Easy
Less than 15 mins
Pliers, Wrench set

Really easy--unscrew screws, pull element out, unclip wire connection. Re-clip to new burner, put back in--done. Saved a $100 tech trip PLUS double mark up on part!

Was this helpful?

The old element caught fire.

1 person found this instruction helpful.

Kyle from Jacksonville, FL
Really Easy
Less than 15 mins
Nutdriver

Unscrew the old one and unplug the wire leads. Then plug in the new one and bolt back up.

Was this helpful?

oven heating element

1 person found this instruction helpful.

Simon from New Port Richey, FL
Really Easy
Less than 15 mins
Nutdriver

I just removed two screws. Pulled the element out, unhooked the wires. plugged the wires into the new element screwed it in and was done

Was this helpful?

Lower element wouldn't heat

1 person found this instruction helpful.

John from Elizabethville, PA
Really Easy
Less than 15 mins
Nutdriver

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, replaced witht he new element

Was this helpful?

Oven bake element would'n heat

1 person found this instruction helpful.

James from Wyndmoor, PA
Really Easy
Less than 15 mins
Screw drivers

Removed the racks first. Then removed the two screws that held the element in place.
I then pulled the element out about three inches
exposing the connecting wires.Each wire has a female slide type connector just disconect each one and then connected the new element .
Attach new element by reptacing the two screws.

Was this helpful?

MEF302PBDB Kelvinator Range - Instructions