Models
>
MEDB800VQ0
MEDB800VQ0 Maytag Dryer - Overview
Sections of the MEDB800VQ0
[Viewing 3 of 3]Keep searches simple, eg. "belt" or "pump".
Door Catch
PartSelect #: PS11748369
Manufacturer #: WPW10111905
This replacement door catch is for your dryer door. If the catch is broken and the door will not stay shut, the dryer may not turn on. Use a putty knife to pop out the existing door catch by the locki...
$7.37
In Stock
Lint Filter
PartSelect #: PS1491676
Manufacturer #: W10120998
The filter collects lint during the drying cycle. This filter is 12 1/2 inches wide and 10 1/2 inches deep. Replacing the lint filter is an easy repair which requires no tools. When replacing the lint...
$61.46
In Stock
Thermostat, Internal-Bias
PartSelect #: PS11746740
Manufacturer #: WP8577274
The internal-bias thermistor (Thermistor, Dryer Thermister, Dryer Thermistor) prevents the dryer from overheating by monitoring and controlling the temperature of the inside of the dryer drum. It is l...
$47.74
In Stock
Roller Support Tri-Ring
PartSelect #: PS11755850
Manufacturer #: WPW10512946
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pul...
$13.42
In Stock
Leveling Foot
PartSelect #: PS1609293
Manufacturer #: 49621
If your washer shakes or vibrates loudly when it reaches its max speed, check that the leveling legs are even. To ensure that the washer is firmly on the ground using all four legs, adjust the legs so...
$11.40
In Stock
Heating Element Connection Wire Kit
PartSelect #: PS334206
Manufacturer #: 279457
This kit is used for electric clothes dryers, and it comes with a yellow wire nut.
$11.06
In Stock
High Limit Thermostat and Thermal Cut-Off Kit
PartSelect #: PS334387
Manufacturer #: 279973
Also known as Thermal Cut-Off kit. The thermostat acts as a safety mechanism that keeps the dryer from overheating and the fuse is like a backup system - it's set to trip at a higher temperature than...
$53.28
In Stock
Moisture Sensor
PartSelect #: PS11741408
Manufacturer #: WP3387223
This is the moisture sensor for your dryer. It helps detect the amount of moisture in your clothes during the dryer cycle. If you notice your clothes are still wet after an automatic dryer cycle is do...
$10.72
In Stock
Light Bulb - 10W
PartSelect #: PS11739347
Manufacturer #: WP22002263
This ten watt appliance light bulb is two inches tall. It is used with both washers and dryers.
$16.32
In Stock
Screw, 8/18 x 3/8
PartSelect #: PS11746840
Manufacturer #: WP90767
This screw is sold individually.
$5.42
In Stock
Idler Pulley Wheel and Arm
PartSelect #: PS11756154
Manufacturer #: WPW10547292
The idler pulley wheel serves to help the belt to rotate the drum. This arm is what attaches to the idler pulley wheel.
$39.41
In Stock
Questions And Answers for MEDB800VQ0
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Frances
January 13, 2020
Controlls light op except for time dry will not show below 59 minutes have done the diagnosis test. Get a co code or f3. Ordered a controll board but that was not the problem.
For model number MEDB800VQ0
Hello Frances and thank you for writing.
The "F3" fault code is displayed because the dryer is not heating. The first thing to check and verify is the voltage supply. The dryer must have 220 volts or it will run but not heat.
We suggest to try a hard reset:
Go to your breaker box and shut the breakers for your unit off, wait 5 minutes and then turn the breaker to on again. That should hopefully clear this problem. We hope this helps. Please contact us anytime if you require further assistance.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Begona
April 11, 2023
Look for the piece that open and closes the door
For model number MEDB800VQ0
Hi Begona, thank you for reaching out. According to our research, the part you are looking for is the hinge, part number PS11746573. Glad to be of help!
Was this helpful?
Thank you for voting!
Related Parts:
- < Prev
- 1
- Next >
Common Symptoms of the MEDB800VQ0
[Viewing 9 of 9]Door won’t close
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Too hot
Fixed by
these parts
these parts
Show All
Not Heating
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Marks left on clothes
Fixed by
these parts
these parts
Show All
Touchpad does not respond
Fixed by
these parts
these parts
Show All
Won’t Start
Fixed by
these parts
these parts
Show All
Door Pops Open
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
felt strip came off lint screen
-
JEFFREY from FALL RIVER, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
219 of 271 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer door catch broken
After a few years of slamming the dryer door (at least that is what my husband says), the catch on the dryer door broke. Using pliers (I used needle nose) squeeze the outer edges of the catch together (vertically). With it compressed, it should slide out easily. My husband had jacked with ours prior to the repair, so the broken piece i
... Read more
n the door was actually sideways and would not fit through the hole. Using a screwdriver, I pushed that piece into the door (it lives in the door somewhere now). I was then able to slide out the rest of the old catch. Compress the new catch and insert it into the hole in the door. Push it in until it clicks into place. DONE! Happy Drying!
Read less
Parts Used:
-
Tammy from Clute, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
148 of 155 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My Dryer Was Not Heating Up.
I asked for advise, looked around and priced heating elements and thermostats. This was the best combo offered for the price given. It was shipped and received it very quick. Installed it and 5 minutes later, she was running like a champ!
Parts Used:
-
roberto from houston, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set, Wrench set
161 of 352 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!