Turn off breaker in electric panel fore stove. Put screw driver into slots in front of glass top surface. Pry top up carefully until top pops up.Remove burner dial, remove two philips head screws holding switch. Lift top carefully and prop up.With new switch close remove wires from old switch one at a time and place on new switch. Place n
... Read moreew switch back in place, securing with philips screws. Remove prop and carefully press top down until it snappes into place.Replace dial, turn breaker back on and try burner.
Read less
Was this helpful?
Thank you for voting!
Burnner would go to high setting no matter what the setting was.
4 of 4 peoplefound this instruction helpful.
Neal from MONROEVILLE, IN
Really Easy
15 - 30 mins
Pliers, Screw drivers
Shut off power at breaker box , pull stove away from wall , remove Phillips screws from back of range pull knob off of switch . Look to see how switch is oriented remove 2 screws that hold switch in . Remove one set of wires at a time and place on new switch in same location . Put back together in reverse order .
Was this helpful?
Thank you for voting!
i sat a tupperware bowl on a hot burner and it stuck to the burner so i had to replace it
3 of 4 peoplefound this instruction helpful.
judy from palatine, IL
Really Easy
15 - 30 mins
just plugged it in!
Was this helpful?
Thank you for voting!
Burner control switch stuck on High
3 of 4 peoplefound this instruction helpful.
John from NACOGDOCHES, TX
Easy
30 - 60 mins
Nutdriver, Screw drivers
Pull out the range...hardest part. Remove back panel. Remove/install switch PS, This is second switch I had to replace. Try making them in the United States.
Was this helpful?
Thank you for voting!
Front 8" burner stuck on high no matter where dial was set.
2 of 2 peoplefound this instruction helpful.
Dale from SAINT PETERS, MO
Really Easy
30 - 60 mins
Pliers, Screw drivers
This range was easy. Only 4 screws under the front panel that allows the panel to come off. No need to pull the range out for back screws.
Replacement part was exact and worked perfect.
Turn off the circuit breaker for the range.
Remove the 4 screws under the front panel, one on each end and one one each
... Read more side of the display/control panel.
Pull the bottom of the front panel out about 30 degrees and lift off the top.
Once panel is off pull of the dial knob, remove the two screws for the control and swap wires on at a time with the new one.. Reverse the procedure and all is good. You may need to use needle nosed pliers on the spade connectors if they are too tight to pull off by hand.
Read less
Was this helpful?
Thank you for voting!
light would stay on all the time saying burner was on although it wasn`t
2 of 2 peoplefound this instruction helpful.
Joseph F Gott from FELTON, DE
Very Easy
15 - 30 mins
Pliers, Screw drivers
unplugged power took the back panel off unplugged the 5 wires removed knob by grabbing and pulling off took two screws out of front panel removed the switched put new switch in place and reversed the procedure went very smooth know problem at all any one with any kind of ability should change this switch in know time at all
Was this helpful?
Thank you for voting!
Burner Failed
3 of 6 peoplefound this instruction helpful.
PETER from ROSEVILLE, CA
Really Easy
Less than 15 mins
Unplugged old burner,plugged in new one
Was this helpful?
Thank you for voting!
replacing old drip bowls
1 personfound this instruction helpful.
Marion J. from Palmetto, FL
Really Easy
Less than 15 mins
It was so simple & the parts fit perfectly. I appreciated all the help from your sales lady. Thanks again.
removed several screws, removed old controller, installed new controller buttoned back up works perfect
Was this helpful?
Thank you for voting!
could not regulate element
1 personfound this instruction helpful.
Billy from LE ROY, WV
Very Easy
Less than 15 mins
Screw drivers
replaced control
Was this helpful?
Thank you for voting!
burner swith not working properly
1 personfound this instruction helpful.
leland from CARTHAGE, NC
Very Easy
Less than 15 mins
Pliers, Screw drivers
removed 4 screws lifted off the face with switches replaced the bad switch and put the face plate back on. if you have any concerns just watch the video , part select has posted its great
Was this helpful?
Thank you for voting!
Drip Pans were stained and burned on.
1 personfound this instruction helpful.
Sandra Collignon from SANTA CLAUS, IN
Really Easy
30 - 60 mins
Replaced drip pan. Notch did not want to match the burner notch. Was a close fit bit with a little pressure made it work.
My Orders
