MDB4000AWB Maytag Dishwasher - Parts

This silverware basket is gray in color and measures 8 inches wide by 11-1/2 inches high by 12 inches deep. The silverware basket is used to hold small utensils such as forks, spoons, and knives during dishwashing. The manufacturer has redesigned this part to be a complete, full basket with a handle and covers. The basket comes apart in t...Read morewo pieces if you prefer to place them along the sides of your dishwasher instead of at the front section of your bottom dish rack. To prolong the life of this part, try to place utensils into the holders carefully instead of dropping them in.

This lower dishrack roller is less than two inches in diameter. It is made entirely of white plastic. If you find that your dishwasher is making loud noises or the lower rack is getting stuck when you are moving it in or out, it could be that the lower wheel assembly needs to be replaced. The dishrack wheels allow for easy movement of the...Read more dishrack in and out of the dishwasher. These rollers tend to wear down at the same speed, so it is recommended to replace both pairs at the same time. Open your dishwasher and remove the bottom rack, locate the locking tab, and rotate until it easily slides out of place. Slide the new wheel over the shaft and locate the locking tab to snap back into place.

This dishwasher door gasket, or door seal, allows the dishwasher door to have an airtight seal when closing the door. No tools are required for this installation, simply remove the existing gasket and press the replacement gasket into the channel around the door. It is recommended to clean the channel while the gasket is removed. This par...Read moret may need to be replaced if the existing one is cracked, broken, or hardened, possibly causing water to leak through the door while it is running. This part is sold individually, and is sourced from the original manufacturer.

This dishrack clip is intended for use with dishwasher dishracks that have adjustable pegs. This clip is only about four inches long.

This upper dishwasher dishrack roller, also known as a dishrack wheel, allows you to roll the dishwasher rack easily on the support rails. If your dishwasher rack is disconnected or the rack is broken, then replacing this part might be the solution. The first step in this repair is to remove the upper dishrack from the track, the next ste...Read morep is to remove the defective rack roller and replace it with the new one by sliding it onto the shaft and locking it in. No tools are required for this replacement and customers rate this project as easy. The roller is entirely made from plastic and is just over an inch in diameter.

This is a rail stop for your dishwasher. No tools are required for this repair. it simply pops on and off the end of your slide rail when pressing the locking tab. This part is sold individually, so it is recommended to check the opposite rail stop on your dishwasher in case it needs to be replaced as well. The rail stop is located at the...Read more end of the upper slide rails which hold the upper dishrack in place. The rail stop prevents the upper rack from sliding completely off the slide rails. This part is gray in color and approximately 1.5 inches wide.

The door spring retainer is used in dishwashers. It attaches and holds the door spring to the support frame. If your dishwashers door keeps crashing, or both the door and dish rack are falling apart, then replacing the door spring retainer, which provides more flexibility, could be the solution to your symptoms. Before starting this proje...Read morect make sure to unplug the dishwasher as well as shut off the water supply before installing the spring retainer. Tools are not needed for this easy repair. Refer to the manufacturers installation instructions for best results and accuracy.

Sold Individually. White in color.

This rack comes complete with four attached wheels and the rack may differ in appearance, but will function same as original part.

This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This clamp is used to securely attach a hose to another part of your appliance, which helps prevent leaks from those connections. Depending on th...Read moree appliance, it can attach hoses to drain pumps, water inlet valves, pressure switches, and injector nozzles. We recommend you refer to model-specific diagrams for appropriate uses and exact placement. This hose clamp is made of metal, and is sold individually. To access and replace this part you will need a nut driver, pliers, and screwdrivers. Before you begin any repair work, make sure you have unplugged your appliance, and shut off the water supply if applicable.

This genuine inner door foam insulation strip, sometimes known as bottom seal foam, is used to create a waterproof seal that helps prevent leaking from the door area of the dishwasher. The existing insulation strip may leave a sticky residue or leftover disintegrated strip that must be scraped off before installing the new strip. Residue ...Read morecan be scraped off with a putty knife. Be sure to remove all residue and clean surrounding areas of the dishwasher build. It is strongly recommended to check other sealant parts on the dishwasher door such as the door gasket and dispenser grommet to ensure the leaking issue is fully solved.

This part senses when the dishwasher door is closed so the cycle can start, and prevents it from starting if the door is not closed. If the dishwasher will not start or will not close, you may need to replace the door switches and holder assembly, also known as the door latch assembly. The dishwasher will not start if this part is defecti...Read moreve. It includes two switches and the holder, this part does not include the handle or screws. Tools needed are T20 torx driver, needle nose pliers, and 1/4 inch nut driver. This is a genuine OEM part that is sourced directly from the manufacturer.