MB536BB1 General Electric Range - Instructions

pull out, push in

Did it By Hand
Your Shipment Time Excellant
Order it Mon. Received it Wed.


Thank You

Easy

Of course the first thing is to turn off the breaker, Unplug the appliance, pull the two electric feed wires off the old element. Then remove the four screws that hold the fan guard in, After that the two screws that held the Bake Element in place. Then reverse the process to install the New Element. Took about twenty mins. from start to ... Read more finish. Just Like New. And thanks to Parts Select for their prompt service, Had the new part in two business days.

While I appreciate all the various parts available from PartSelect, I was disappointed that the only heater element that was approximately the right size and shape for my wall oven had push-on prongs. My original was screw-on.

Thus, I had to (very) carefully drill through the somewhat thick metal tabs to get screws into them ... Read more . This meant holding the tabs with a pliers while I drilled them out to make sure that I did not break off the tab. Then, I increased the hole size by using increasing diameter drill bits. I let the screws self-tap, but again this was done carefully to avoid breaking off the tabs. Finally, I found that the part of the new heater element going through the back wall of the oven was an inch or so longer than the original. This did not seem to cause a problem of overheating outside the oven. At least not so far!

First of all I did this repair because the wire to the burner shorted out. I did the wire portion first - only then did I know I needed the switch kit. (The burner was operating while my old swithch was OFF). The first (wire replacement) repair took about 10 minutes - I followed the guidance on this web-site. The second repair (The switch ... Read more ) took about 20 minutes. The switch ws not the same as the original. Just be careful to mark each wire as you remove them from the old switch's posts. The posts on the switch are marked and you need to place them on the like-marked corresponding posts on the new switch. All is well, my burner is operational.

Your "virtual repairman" was fantastic. I would have purchased the wrong part without trhe diagnostic service. It said that 53% of the time the infinite switch was the problem. In my case it was 100%. Why I put up with this problem for 6 years I will never know.

Repair job was easy but longer than the 15 minutes that it said ... Read more it would take.

saw when heating the stove up the bottom element wasn't getting hot. got part number and looked up online and ordered

First I shut off the power at the power box. Second I removed two screws in metal plate. Third I unplugged the two wires. Repeated steps backwards and it works great.

Removed old, and replaced with new, heating element! Maybe 10 seconds.

First i removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Very simple and easly job.

I ordered to correct part from PartSelect with relative ease given I know nothing about oven repair. What's even more amazing, my wife who is not mechanically-minded, took the element home and replaced the broken one in 15 minutes with nothing but a pair of pliers. We live 22 miles from town so a repairman would have cost over $100 just ... Read more to show up. Total cost = $36!

With the oven unplugged, I removed the protective plate from the back of the oven, and then I unplugged the old element from the contacts. There were two screws holding in the element inside the oven- after unscrewing these, the old element slid right in. After reconnecting everything and plugging the oven back in, all was good. Pretty ... Read more simple.

I first read the repair stories on this website. I turned off the power to the range in the power box. I removed the 2 screws, pulled out the old heat element a little, then disconnected the wires from the connectors. I just reversed the steps to put the new one in and viola. Really simple. Parts came really fast too. At first I ord ... Read more ered the wrong part b/c I didn't look up the part using the model number, I just went by t he picture and the manf. name. I returned that and got refunded promptly, so make sure you order by model number b/c parts are made different for each appliance model.

A breeze! Part was perfect replacement, snapped in place without tools, and heated almost immediately.