MA1301S LG Microwave - Instructions

Part select made it very easy for me to purchase a replacement plate, which I didn’t think I was going to be able to find so thank you part select for having what I needed

Take cover off microwave. Check door switches to determine which one was faulty.Remove and replace faulty switch.

i unplugged the unit,unscrewed the outer shell so that all the wiring and internal components were visible.starting at the first of three micro switches i removed the slip on terminals installed the alligator clips too the wires so the switch would now be bypassed.i made sure the wires and clips were not touching anything plugged unit in ... Read more and it worked.i then installed the new switch and closed up the outer shell

Remove screws, take microwave cover off. Pull light assembly and unplug bulb. Replace with new bulb and snap back in place. Screw cover on and your done.

I verified I had 120 volts going into transformer when the microwave was supposed to be running. The capacitor and HV diode both tested good. Be sure to discharge the capacitor before working in this area. This isolated trouble to either the transformer or magnetron. The windings of the transformer measured good. So ordered a magnetron. I ... Read more t was very easy to swap. There were 4 screws and one connector. This fixed our microwave.

I want to preface this review by stating that I do some DIY from YouTube, but have no experience in electronic repair. The microwave is over the stove with the extendavent. First I unplugged the microwave, removed the vent and started to unscrew the microwave from the mount. I used a power drill to speed things up. I was able to remove ... Read more the microwave on my own. I unscrewed the lid on the microwave and took the lid off and there is the magnetron. I opened up needle nose pliers to have each end touch the terminals of the capacitor (holds the power, Dangerous). I made sure to keep my hands on the rubber handles and avoid touching the metal part of the pliers. I used the pliers to remove the plug of the capacitor to the magnetron as well. The magnetron has 4 screws (2 top, 2 bottom). There is a magnet that can hold the screws to keep from falling but I’d still recommend a screwdriver with a magnet on the end. The magnetron has another set of wires connected by a metal bracket like a holder, not really connecting any wiring to the magnetron itself. I had to unscrew 1 screw to removed that. Adding everything back on was easy, same steps back. I plugged in the microwave and tested a cup of water before I mounted it back above the stove. Voila! I did need my wife’s help to hold the microwave on the hinge while screwing into the mount. It doesn’t take a lot of muscle for the help. $85 for the part and ~40 mins to fix a $400 microwave!

Used a Motor cycle Jack to remove both unites combined. Removed side panels exposing internal working parts. Removed nonworking Magnetron and replaced it with new Magnetron. The process was completed in about 1 hour.

Problem was due to a faulty door switch. Replaced with a new switch and the microwave now works fine! Only thing that was tricky was that LG uses the hex screws with a peg in the middle to keep the microwave cover on. Had to use a small screwdriver and pliers (on the screwdriver) to unscrew the screws.

unplug the unit then pull down , lot of screws are on top. open the cover . you could see the parts that need to replace on the right hand side (heavy side). disconnect wires then test the parts that need to replace by a tester to make sure that it's really broke .then unscrew part and replace .

I UNPLUGGED the microwave and removed the cover, using a phillips and a Torx screwdriver for the machine screws. I set these screws aside, so as not to confuse them with the later encountered screws. I photographed the magnetron to assure proper placement of the 6 phillips machine screws involved in reassembly (marking the the locations ... Read more on the old magnetron would do as well. I marked the old magnetron "old", to avoid later confusion. I removed the two screws holding the shields to the magnetron. I removed 3 of the 4 screws holding the magnetron to the microwave, leaving one of the top screws. I held the magnetron securely and removed the last screw, pulling out a the part of the magnetron that penetrated the microwave. I installed the new magnetron in reverse order. One problem I encountered was locating one of the six screws, which had been pulled into the old magnetron by magnetism.

Partselect sent me the right thing in two days! The whole process was easy as pie.

"PIECE OF CAKE" Removed cover,removrd bulb, replaced bulb, replaced cover. "PIECE OF CAKE" P.S. Wife is happy.

You have to remove the cover which in my case was a little more difficult because the unit is wall mounted and has a frame around it. That was the hard part. Once the mounting frame was removed, you can remove the cover and the light bulb is on the top right side of the unit. One screw removes it and the new one pops right in. Put the cas ... Read more e back on reinstall it in the wall and voila...piece of cake.

you will a security socket T20. this unit was installed over oven, remove trim cover,remove screws holding unit in place,I used a helper to get the unit out, once out you have to remove all the screws holding the cover on,on two of the corners they use a security hex screw so you need a special socket for that. remove the door latch switc ... Read more h,take your time or you will break tab holding switch in. ask me how I know.but super glued broke piece in place and plugged wire back in.the new latch may have a second pin but look at old one and plug wires in the same way.the light bulb does not screw out so I had to purchase the entire unit.total cost under a $100.00 to do repair.

We got a a carbon steel but and drilled out the stews and put in regular screws. We also had trouble getting the cover back on and ended putting 2 more screws on the left side which had none. The installation was the easiest part of the installation.