LWM204WC Amana Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Started making loud screeching noise(bad Bearing)
1 of 2 people
found this instruction helpful.
-
Michele from Lebanon, PA
- Easy
- Less than 15 mins
-
Pliers, Screw drivers, Socket set
Turned water off,tilted unit forward,removed lower rear cover,removed belt,laid towels around ,removed inlet hose and exit hose off pump,removed 3 screws holding pump,removed pump and installed new one,reversed order of disassemble, has been running great ever since.
Was this helpful?
Thank you for voting!
discharge pulley assembly bearing going out on it.
1 of 2 people
found this instruction helpful.
-
Milton from bartlett, IL
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
Went to website, looked up make and model, looked at photo's discription, studied it, and then went in and removed front panel, turned off water, removed clamps holding hoses too dishcharge pump, mopped up water, and then just reinstalled new piece, the way the old came out, re attached belt to pulley assembly, turned water back on, and d
... Read more
id a test for leakage and wala washer back in working order in less than an hour, and saved hundreds of dollars with out maytag repair man.
Read less
Was this helpful?
Thank you for voting!
Washing machine began making a screeching noise but only during the spin cycle - when it was emptying the water from the tub. After a few uses the machine just stopped working.
1 of 2 people
found this instruction helpful.
-
Patricia from Modesto, CA
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
The pump was easy enough to replace. Access panel in the back and 3 screws and it was off and back on in less than 20 minutes. It was putting the belt on that gave me the most trouble even though one of the pulleys moved to allow for easy replacement it did not move enough. It took me another 30 minutes just to get the belt on. I fina
... Read more
lly decided to place the belt on the two smaller pulleys and save the larger one for last and it went on with no trouble at all. Learn from my error =]
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Washer making loud noise and tub off balance
1 of 2 people
found this instruction helpful.
-
Hollee from Rancho Mirage, CA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
I followed Gary from Sioux City IA instructions. Very well explained.
Was this helpful?
Thank you for voting!
noisy out of balance during spin cycles
1 of 2 people
found this instruction helpful.
-
Ronald from Wading River, NY
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Socket set
I followed the instructions that other posters suggested. The springs were the toughest part to remove and reinstall. Having my wife push the tub enabled me to use vice grips to get them back on. Read about the coins or washers to spread the springs too late... would have helped. Running a wash now and it's spinning great and no noise
... Read more
!
Read less
Was this helpful?
Thank you for voting!
Tub cracked while replacing snubber
1 of 3 people
found this instruction helpful.
-
Nicholas from King of Prussia, PA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
Remove tub assembly per snubber replacement procedure.
Place tub assembly on top of a milk crate open-side up.
Support tub assembly on milk crate with 2x4's to protect pully from damage.
Remove agitator from tub assembly.
Press down on tub assembly cap, release tabs and remove tub assembly cap.
Remove inner tub ... Read more from tub assembly.
Mark tub frame with location of outer tub air bell for ease of reassembly.
Remove outer tub from transmission assembly.
Replace inner tub gasket
Replace outer tub gasket
Problem encountered was that the replacement tub had a defective air bell. The washer consequently did not detect fill level and subsequently overflowed flooding the laundry room. The bell looked ok visually. Blowing into the air tube while plugging the inside hole with a finger revealed a pinhole leak in one corner of the PP weld. PartSelect was prompt with replacement, but the job had to be redone in its entirety.
Always test the air bell before installing an outer tub.
Place tub assembly on top of a milk crate open-side up.
Support tub assembly on milk crate with 2x4's to protect pully from damage.
Remove agitator from tub assembly.
Press down on tub assembly cap, release tabs and remove tub assembly cap.
Remove inner tub ... Read more from tub assembly.
Mark tub frame with location of outer tub air bell for ease of reassembly.
Remove outer tub from transmission assembly.
Replace inner tub gasket
Replace outer tub gasket
Problem encountered was that the replacement tub had a defective air bell. The washer consequently did not detect fill level and subsequently overflowed flooding the laundry room. The bell looked ok visually. Blowing into the air tube while plugging the inside hole with a finger revealed a pinhole leak in one corner of the PP weld. PartSelect was prompt with replacement, but the job had to be redone in its entirety.
Always test the air bell before installing an outer tub.
Read less
Was this helpful?
Thank you for voting!
machine woulden't spin properly
1 of 3 people
found this instruction helpful.
-
Richard from Ponte Vedra Bch, FL
- Really Easy
- Less than 15 mins
-
Nutdriver
diagnosed a loose belt-- ordered and received same -- installed and set to proper tension that was simple.
Was this helpful?
Thank you for voting!
Pump was making a grinding noise.
1 of 3 people
found this instruction helpful.
-
Daniel from Hinsdale, IL
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
I tilted the machine on it's back to remove the drive belt. You could feel the friction in the pump when you turned the pulley. I set the machine back down and removed the back cover (4 screws). I removed the two hoses with a pair of pliers. I used a small socket set to remove the three mounting screws. I ordered the pump. I
... Read more
reversed the process to put it back together. It took about 35 minutes to determine what the problem was and to remove the pump. It took about 20 minutes to put it back together.
Read less
Was this helpful?
Thank you for voting!
Washer was leaking water.
1 of 3 people
found this instruction helpful.
-
Steven from Atlanta, GA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Socket set, Wrench (Adjustable)
Removed front of washer following instructions on partselect.com (used putty knife to release catches). Removed hoses and belt from pump, then removed and replaced the pump. Reattaching the belt was the only awkward task.
Was this helpful?
Thank you for voting!
Noisy Pump
2 of 7 people
found this instruction helpful.
-
Frederick from Yuma, AZ
- Really Easy
- 15 - 30 mins
-
Nutdriver
I placed the washer on a couple of work-horses so I could have access to the belt underneath. Then I used my nutdriver to removed the lower back panel. Disconnected both of the hoses, and removed the pump with my nutdrivers. Placed the new pump in place, placed the belt back on the pump's pully, tightened down the pump. I then plugged
... Read more
in the washer and put a little water in the washer to test that everything was working. After confirming that everything worked, I replaced the lower back panel and put the washer back in business. 30 minutes from beginning to end ... and a good time was had by all.
Read less
Was this helpful?
Thank you for voting!
Bearing on pump making noise and would go out soon.
0 of 1 people
found this instruction helpful.
-
Marcus from Camarillo, CA
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
I diagnosed the bearing by putting a 3/4 inch rubber hose up to my ear. I pointed it around until isolating the noise to the pump. The bearing was not servicable without replacing the pump. After diagnosing the problem I ordered the part. Getting the part from PartSelect.com was a snap. It arrived in one day. In 15 minutes I had it back t
... Read more
o gether and working quiet and smooth.
Read less
Was this helpful?
Thank you for voting!
no cold water
1 of 4 people
found this instruction helpful.
-
juan from moreno valley, CA
- Really Easy
- 15 - 30 mins
-
Pliers, Socket set
I pulled the top ofthe washer up, I disconnected the cold and hot water hoses, took the 2 bolts off with a socket and pulled the water valve from the top. I used the pliers to take the pressure ring off and pulled over flow hose off. I pulled the four wires off with pliers. Put the new water valve in reverse order...easy.
Was this helpful?
Thank you for voting!
noisy pump
0 of 1 people
found this instruction helpful.
-
Tery from Orange, CA
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Removed back plate, tilted up washer removed pump removed belt. Then replace pump and then replaced belt
Other Parts Used:
Was this helpful?
Thank you for voting!
dead pump
1 of 4 people
found this instruction helpful.
-
Andre. M from Glendale, CA
- Really Easy
- 15 - 30 mins
-
Socket set
I first opoen the front panel of the washer. That was a bit tricky. Had to slide a thin blade between the top of the washer and the front panel, pushed in to release the "clamp" and gently raise the top, it hinges on the back.
The rest was undoing three bolts, refit the new pump and put the belt back on.
The part cost me less ... Read more then $65.00.
The repair estimate by the local repair man was $ 250.00.
I am very happy.
Thank you PartSelect.
Andre M. Roberty
The rest was undoing three bolts, refit the new pump and put the belt back on.
The part cost me less ... Read more then $65.00.
The repair estimate by the local repair man was $ 250.00.
I am very happy.
Thank you PartSelect.
Andre M. Roberty
Read less
Was this helpful?
Thank you for voting!
washing machine filled with water, nothing else happened.
0 of 1 people
found this instruction helpful.
-
Ellie from Eastview, KY
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Spoke with a trusted repair man, described the problem best as I could. I smelled a burning rubber smell. Got on Internet for troubleshooting problems, 77% likely a drive belt. BINGO! Ordered a new belt, took old one off, cleaned the pulley ( it had burnt rubber stuck on it, difficult to remove) lightly sanded pulley just so it would be r
... Read more
eally smooth. replaced belt. Magic, it worked. I am no repair woman, but carefully listening and explaining helped. Oh, belt is under the very bottom of machine. Very easy to get to, just tilt back and lodge at an angle and make sure it doesn't move.
Read less
Was this helpful?
Thank you for voting!