LSWF388HVS (ASSEEUS) LG Washer - Instructions

Honestly youtube but pretty simple install.

Totally dis-assembled this washer to check the bearings and drum plus fix the pump problem. We wash dog blankets occasionally and found the little drain hose from the front door gasket was clogged with hair. It makes a 90 degree turn and it gets caught there. THAT fixed the smell issue. As far as the pump replacement goes its quite easy. ... Read more Videos online are your friend.

Watch the video to repair and follow along

Simply inserted new plunger/magnet back into door with thumb&finger until you hear the little locking tabs click. No tools required.

Follow the LG washer video.

E. Z. hardest part (which isn't hard) was moving the appliance to reach the back, then putting the appliance back into place. the actual repair (swapping out valve) took less time than that to do.

Use just your finger to push it into place. VERY EASY

Unscrewed the old part; screwed in the new part and said a quick prayer - LOL!
The part worked great, but I wanted to mention how quickly I received the part!
I would definitely order from this company again!

Removed top panal found broken parts and pieces, replaced spring and plastic spring holder. Straightened out and reattached drum front boot.

Disconnect washer - pull out and turn on it's right side. Remove bottom plate (2 screws). Water intake valve is attached to water line. Disconnect water line. On the other end of the pump is a rubber hose. Disconnect hose by using a pair of pliers to open pipe clamp. Disconnect the electric line by pulling the pronged plug out of th ... Read more e pump. The part is composed of the pump and a metal mounting plate. They are connected by 4 screws. Remove the screws and pull out the back half of the pump. The front of the pump is attached to the washer frame by 2 screws. When removed you will notice an o-ring that forms the seal between the two halves. Remember this when installing the new pump. You will have to take the new pump apart because the whole part will not fit through the frame opening, thus the need to make sure the o-ring is properly seated. You can either install the mounting plate to the frame then attach the pump half or with half of the part in front of the frame and the other half behind the frame connect the two, then attach it to the frame. Reconnect incoming water line using teflon tape and a crescent wrench. Reconnect out-flow line with the pipe clamp and attach the power line. Since you have to take the new pump apart make sure the o-ring is properly seated as it will have a tendency to fall out. Reassemble the rest.

From previous experiences with other washers, i.e., Sears, I decided it was the mother board or the door latch component. Ordered the electronics and then the discovery that LG has an APP for iPhone. Loaded the app, placed the phone next the washer and pushed the button on the washer. The washer "talked" to the iPhone and within 15 sec ... Read more onds it told me there was a problem with the thermistor. Opened the back of the washer and looked under the tub for the thermistor and found the 2 connecting wires were hanging loose. Put the wires back into the thermistor connection and everything was back working.

I youtube searched this problem and found a video from partselect. I watched the video, purchased the part, and followed the video instruction step by step to repair the washer. Part with tax and shipping was $52.

Disassembled washer, replaced bearings, seals and gasket. Watched instructional video to familiarize myself with the repair. Followed all steps as recommended, repair was straight forward without any surprises. Hardest part was removing the drum from the machine, somewhat heavy. Disassembled and replaced all bearings, seals, spider and ga ... Read more sket. Reinstalled in reverse order. Note: Upon tear down, I found the seal was pushed out, causing the bearing failure. I also found that the seal was installed incorrectly from LG. They have the seal lip facing the bearings, should be facing the water. This repair seems to be difficult, but was fairly self explanatory. All plug ins are color coded, all hoses are accessible with little effort. If you have basic skills you should be able to handle this repair.

you tube it , not to hard to install

Followed the video supplied by this site and everything was as described!