LSMX211ST (ASTCNA0) LG Refrigerator - Instructions

1. Shut off water to refrigerator. 2. Removed bottom sheet metal cover (6 screws). 3. Removed leaking water inlet valve assembly from refrigerator (1 screw). 4. Remove water inlet tube (loosen nut) and tube back to refrigerator (pull from water valve after remove cotter pin washer). 5. Detach two electrical wire harnesses. 6. Install new ... Read more water inlet valve assembly to refrigerator (1 screw). 7. Replace both water tubes to water inlet assembly. 8. Re-attach both wiring harnesses. 9. Turn water to refrigerator on. 10. Check for leaks. 11. Re-attach bottom sheet cover (6 screws).

Video makes it look easy. Kenmore refrigerator does not have "groove" along the right hand side of switch that allows for pushing down on release. Used a thin screwdriver to get under to push while holding switch edge with pliers. Kept slipping. Tape sides to avoid scratching inside of refrigerator.

I pulled the gasket off and installed the new one. It was very easy. All I had to do was to push the new gasket in place in the grooves in the door. The gasket I received was identical to the one I replaced.

The Refrigerator now runs very quite.
After watching several videos I started on mine and found that it was a bit different than any in the videos. However all but the back panel was shown and that was helpful.
The back panel was a bit difficult but a hair dryer seemed to help .
All in all it was a good choice to do it myse ... Read more lf as it was done quicker than waiting on a repair man.

So easy I couldn't believe I'd done it so quickly. Two minutes from start to finish. Pull the old one off and press the new one in.

Replace the ice container. There was a break in one of the things that held it in.

Insert the top first and then twist to insert bottom

The refrigerator had the above code and when I check on YouTube, it explained that the defrosting was not working properly. It was taking more than 80 minutes to defrost. I ordered the Temperature Sensor first and it was not the issue. I also ordered the Defrost Temperature fuse or the Thermistor. I had to defrost the refrigerator first ... Read more by using a portable heater to get it done quickly. (See Youtube on how to get to the Defrosting Unit inside the freezer). The Thermistor was the wrong part. I called the Partselect and explained that the part with the heating element is one piece. (Heating Coil Thermistor or Heating Coil). By replacing that piece solved the Error Code issue. I listened to Youtube for the instructions on how to replace the Heater Coil. So if you see the Error Code dH F, you need to replace the Heating Coil, which comes in
one piece and sits on the bottom of the Defrost Element.

Used a little screwdriver to pry the part over and slip it into the holes on the sides. It took longer to find the right screwdriver than to put the part in.

Used putty knife to pry out the old gasket, pressed new one in place. Very easy, done quickly. About 10 minutes.

Sent for replacement,got it took old one off put new one on that was it. Thank you

It was SO easy. No clamps or brackets. Grabbed the gasket with pliers to get started removing it - just pull it out of the deep groove inset around the perimeter of the door. Within one minute I had the old gasket removed. Started installing the new gasket by inserting the top right corner 1st (pushing the new gasket profile into the ... Read more deep groove inset on the door). Working around the top and right side slowly inserting the gasket profile into the deep groove around the entire door. You may have to "adjust" a bit by pulling on the gasket but within 5 minutes I had the new gasket in-place never having to turn off the refrigerator. YouTube has great "how-to" videos. It's easy!

After watching a few iTunes videos I was able to order the light switch from part select and within a week I had the new switch. I had a little trouble getting the switch out. I used a flat screw driver and taped around the edge to keep from damaging the wall inside. I found the clip on the right side and had to use some force to get it p ... Read more opped out, you may need to use pliers to disconnect the switch.

started in a corner of the door and pulled out the old gasket and inserted the new gasket by being sure to start each corner before pushing in the center so it fits good first. extremely easy.

I followed the directions! It was so easy that I bought another switch for my sister's fridge (same as mine). Her light was out too!