- Home
- LSE7804ACE
- Instructions
LSE7804ACE Maytag Washer Dryer Combo - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
broken siphon elbow
7 of 10 people
found this instruction helpful.
-
Larry from Chippewa Lake, OH
- Easy
- 1- 2 hours
-
Nutdriver
I thought it was going to be next to impossible to find a replacement part for an older washer. So my first attempt was to try to epoxy the original part, but the epoxy didn't hold up to the stress. I began thinking about what I might need to make a replacement part which was possible but not very practical. Although I dreaded trying to
... Read more
find this part online, I was very surprised and elated to happen upon PartSelect! Oh, by the way, this washer belongs to my daughter and I nave tossed the paper I wrote the model number on, so the model number was entered as the part number, sorry. At any rate, the the part was reasonable priced, and shipping about standard, but I still saved a lot by doing it myself rather than having a repair person for something this simple. Partselect online lookup made it easy to find the model and drawings to help me find the correct part nomenclature. AND, the part was in stock! So I am pleased with how this venture worked out.
Read less
Was this helpful?
Thank you for voting!
Trying to install the drum belt by reaching in from the front over the top of the blower & motor.
7 of 10 people
found this instruction helpful.
-
Wesley from Tulsa, OK
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
I observed that the top of the dryer was affixed by two screws at each front corner. With these removed the top of the dryer could be easily lifted and with the front support panel removed the drum, drive motor and idler pulley could be accessed. This allowed the installation of a new drum belt in a short period of time. Installing the
... Read more
belt from the front lower left hand side proved very difficult for me but with the top raised and coming in from the top it was accomplished in short order. Thank you, Wesley Harmon
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
black marks on whites and dark
9 of 16 people
found this instruction helpful.
-
ROBERT from MORGAN CITY, LA
- Easy
- 1- 2 hours
-
Socket set, Wrench set
The repair went better then I thought it would go.
the seals went on just fine
the seals went on just fine
Other Parts Used:
Was this helpful?
Thank you for voting!
Washer Leaked Water From Bottom Seal
6 of 7 people
found this instruction helpful.
-
JACLYN from RICE LAKE, WI
- Difficult
- More than 2 hours
-
Pliers, Screw drivers, Socket set, Wrench set
Removed washer tubs inner and outer nut (part # 10 ) on inner was hard to remove and is a reverse thread used hammer to loosen once off removed 1st tub - then removed set screw #17 and then unscrewed mounting s item #29 this again required some hammer tapping to loosen - once off used flat head screwdriver to pry & remove the rubber piece
... Read more
on bottom of outer or 2nd tub -but keep going as the leak will probably be from part #20 tub bearing ( this will save you the time to test and find out it still leaks and have to take apart again after only replacing #29 removed 3 bolts holding tub - disconnected hoses and removed 2nd tub - used rubber hammer to knock out and install #20 tub bearing - reasembled and wow no leaks to cost about $120 - time worked on 3 hrs - only because took apart 2 times - down time on washer 10 days as we didn't order all parts to start with no beer needed but did enjoy a nice red wine - good luck
Read less
Was this helpful?
Thank you for voting!
Door safety switch would not close keeping dryer from running
9 of 16 people
found this instruction helpful.
-
John from Warsaw, IL
- Really Easy
- Less than 15 mins
Shut off or unplugged dryer for safety.
Slipped thin blade putty knife up under bezel of switch to unlatch from the panel and pulled forward to remove the swwitch from the dryer. Unplugged the quick connect terminals (3) from the old switch and plugged them onto the new switch. one of the terminals had gotten quite hot and da ... Read more rkened the insulation so it was replaced with one that was supplied with the switch. that was a cut, strip, crimp process. Placed the new switch into the panel and snapped into place.
Slipped thin blade putty knife up under bezel of switch to unlatch from the panel and pulled forward to remove the swwitch from the dryer. Unplugged the quick connect terminals (3) from the old switch and plugged them onto the new switch. one of the terminals had gotten quite hot and da ... Read more rkened the insulation so it was replaced with one that was supplied with the switch. that was a cut, strip, crimp process. Placed the new switch into the panel and snapped into place.
Read less
Was this helpful?
Thank you for voting!
lid closing to far bumpers missing and fuse block cracked
18 of 43 people
found this instruction helpful.
-
eunice from prestonsburg, KY
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
unhooked power plug removed 2 top screws tilted topfront panel back removed cracked fuse holder replaced with new fuse holder put top cover back on installed 2 top screws plugged in power cord done!
Other Parts Used:
Was this helpful?
Thank you for voting!
The water to the washing machine continued to run into the unit when it was supposed cut off. It continue to fill overflowing the tub of the washing machine and onto the floor. The water had to be cut off at the wall in order to stop the inflow of water.
8 of 13 people
found this instruction helpful.
-
Donnie from Spring, TX
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers
I disconnected both water hoses from the back of the machine. I then unscrewed the panel that holds the water inlet valve. After disconnecting the two electrical connections from the valve and replacing it with the new unit, the job was done.
Was this helpful?
Thank you for voting!
water leak during spin cycle
6 of 7 people
found this instruction helpful.
-
Efrain from Fontana, CA
- Really Easy
- Less than 15 mins
-
Screw drivers, Wrench (Adjustable)
First removed the two lower screws from the front panel. I then unscrewed two screws holding the top(lid) of washing machine. I then lifted the lid and let it rest on its rear hinges. The syphon is removed by unscrewing four screws from the rear of the washer. I then cut the original clamp holding the syphon to the hose. New syphon was in
... Read more
stalled. Enclosed hose clamp was used to tighten around hose. Syphon was then then screwed back to the rear wall of the machine. Easy fix. Water leak solved.
Read less
Was this helpful?
Thank you for voting!
Upper and lower filler injectors broken
6 of 7 people
found this instruction helpful.
-
Henry from Southside, AL
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Power cord out, of course.Popped off the front panel, swinging bottom outward. Wedge shaped protrusions on top of front panel work as a hinge until the bottom is swung out and the entire front lowered. Unscrewed the top--one screw in each front corner accessed from the front opening (removed panel). Panel behind control panel must be remo
... Read more
ved (5 hex head screws). Tilted front of top up revealing broken injector. Retaining screw for injector accessible from behind control panel loosened and broken injector assembly removed. New (easily assembled--snap together) injector slid into holding slot on one side and screwed down with previously removed hex screw. Reassemble in reverse.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Burned out part
7 of 10 people
found this instruction helpful.
-
RAFAEL from CENTERVILLE, GA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Good.
Was this helpful?
Thank you for voting!
door switch broke
9 of 16 people
found this instruction helpful.
-
richard from pleasant valley, NY
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
remove bottom section under door 2 screws remove door 2 screws remove switch by squeezing tabs install 2 new female ends on wires supplied with switch . put switch back in plug in wires .
Was this helpful?
Thank you for voting!
Broken drum belt
8 of 14 people
found this instruction helpful.
-
Robert from Finland, MN
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
I pulled the face of the dry off by removing the two screws on the lower face below the door. I pulled the drum out by removing the two bolts holding the drum mounts to the frame. I put the new belt around the drum and remounted it. The access hole on the lower right corner on the back of the appliance allowed me to turn the drum to align
... Read more
the belt (and turn it right side up) with the pulley. It took a moment to figure out how to re-thread the pulley but was able to do it after only a couple of tries. All in all it was quite easy!
Read less
Was this helpful?
Thank you for voting!
Repairs Were Easy.
11 of 28 people
found this instruction helpful.
-
James from Ventura, CA
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set, Wrench set
Removed top. Removed agitator and tubs . Replaced seals and reassembled.
Other Parts Used:
Was this helpful?
Thank you for voting!
Noisy Dryer operation and eventually no air movement through dryer
5 of 5 people
found this instruction helpful.
-
Russell from ELK GROVE, CA
- Easy
- 30 - 60 mins
Every two to three years, the blower wheel gets chewed out in the center where it attaches to the motor shaft. I have learned the sound of it starting to rattle so I know to order a new blower before the air stops moving altogether. Replacing it is very easy if you have tiny sockets or nut drivers and a pair of snap ring pliers.
... Read more r />When working on this dryer, be aware that the heater wires are always "hot", even when the dryer is not running. You are only likely to touch one at a time so the worst you will feel is 120 volts. The shock probably won't hurt you but you may cut yourself jerking your arm out of the dryer. Best to unplug the dryer or open the circuit breaker before sticking your arm in there!
... Read more r />When working on this dryer, be aware that the heater wires are always "hot", even when the dryer is not running. You are only likely to touch one at a time so the worst you will feel is 120 volts. The shock probably won't hurt you but you may cut yourself jerking your arm out of the dryer. Best to unplug the dryer or open the circuit breaker before sticking your arm in there!
Read less
Was this helpful?
Thank you for voting!
Very old washer was leaking oil and grease drops into the wash water.
5 of 5 people
found this instruction helpful.
-
William A from PITTSBURGH, PA
- Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Followed the procedures recommended for replacement of all the parts included in the Tub Bearing Kit and the Mounting Stem/Tub Seal kit as illustrated in a detailed, 32 minute repair video for the Maytag A606 washer which is available on YouTube. Many difficulties were experienced in the disassembly procedures due to extensive corrosion
... Read more
of tub bearing and tub stem parts (the washer is 47 years old).
I was not successful in using a special tub wrench that was purchased to break loose the old tub mounting stem and its threaded lock nut. The old tub mounting stem, lock nut, and the tub bearing race had to be cut off the threaded support shaft using a saws-all electric tool. Finally, corrosion on the edge of the tub caused problems with water leaks once the tub top and its rubber tub seal ring were reinstalled and the washer was put back into operation. The bottom line is that it may be questionable to attempt major repairs on washers that are 40+ years old and have any extensive corrosion in internal, mechanical parts.
I was not successful in using a special tub wrench that was purchased to break loose the old tub mounting stem and its threaded lock nut. The old tub mounting stem, lock nut, and the tub bearing race had to be cut off the threaded support shaft using a saws-all electric tool. Finally, corrosion on the edge of the tub caused problems with water leaks once the tub top and its rubber tub seal ring were reinstalled and the washer was put back into operation. The bottom line is that it may be questionable to attempt major repairs on washers that are 40+ years old and have any extensive corrosion in internal, mechanical parts.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!