The range thermostat is also commonly known as a stove, oven, cooktop, or range thermal fuse. This thermostat protects your oven from excessive heating, and will shut the oven heat off if excessive heating is detected. This is a genuine part sourced directly from the original manufacturer. You may need to replace this part if your applian...Read morece will not heat properly. It is made of metal and is approximately 1 inch in diameter. This part is sold individually. It is recommended to order a spare, especially if you commonly use the self-cleaning function in your oven.
This temperature sensor, also known as a thermistor, is compatible with various makes and types of appliances. This thermistor uses electrical currents to detect the interior temperature of the appliance it is in and by working with the control board, the board adjusts the level of cooling or heating through its heating or cooling element...Read more, depending on what is needed. If your appliance is being improperly heated or cooled, the temperature sensor may be to blame, and can be tested with a multimeter to check for continuity to see whether it is defective. Check your user manual for exact placement of this thermistor and any diagnostic information.
This is a genuine OEM leveling leg for various models of LG ranges. This leg is used to stabilize and support the range, and if damaged, broken, or missing, will cause your range to rock back and forth. Installing this leg simply requires you to lift on the corner you are installing it under, and then screw it in place until your range is...Read more stable. This approximately 2-inch leveling leg is sold individually, so if your range has multiple legs that are broken or missing, consider how many legs you need to order.
A dual radiant heater supplies heat to a cooking area beneath a glass cooktop. Replacement may be needed when one zone does not warm, only the inner or outer section works, or the element has a visible break. Normal radiant burners cycle on and off, so cycling alone does not prove a failure. Check the control switch and connections first,...Read more then match the replacement by full model number, location, size, mounting points, and electrical rating. Disconnect the range at the breaker and confirm the circuit is dead before service. Handle sharp metal edges and the glass top carefully, and return every bracket, shield, and wire to its original position.
This radiant heater may also be known as a radiant surface element and is a part for your range. The function of this heater is to supply heat to the cooking area that is on the top of the range. This piece is roughly 9 inches long, and 7 inches wide. The most common symptom for needing to replace your radiant heater is if your burner is ...Read morenot heating. Before replacing this part, it is always a good idea to test it for continuity. To make this installation you will need a Phillips screwdriver, and a 14-inch nut driver.
This white surface burner control knob is designed to allow smooth, precise adjustment of heat levels on a range’s surface burner, helping ensure consistent cooking control. Built for regular, everyday use, it offers a comfortable grip and clear turning action to make temperature changes easy and reliable. The knob installs with a simple ...Read morepull-off and push-on design, making replacement quick and DIY-friendly when an original knob is cracked, worn, or missing. Replacing a damaged control knob helps restore proper burner operation while maintaining a clean, uniform appearance on the cooktop.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Donald - For model number LSE3092ST
December 4, 2023
My convection fans run 24/7.
Does this sound like a PCB sub assembly fault?
Hello Donald, thank you for the question. Based on our research, the issue is most probably with the PCB assembly. We would suggest replacing the PCB assembly, part number PS3533964, to solve the problem. It monitors the temperature and controls the oven heat. Glad to be of help!
I only have 3 out of 5 stove top elements working.
Thanks
Hi Philippe, thank you for contacting us. We have found that the issue is with the terminal block, part number PS12715316. The terminal block connects the house power to the range wire harness. We would recommend checking the terminal block to fix the issue. We hope this solves your problem!
Our oven temperature is way below what the display shows
Hi Jacobus, thank you for getting in touch. We have concluded that the issue is with the temperature sensor, part number PS11732697. It measures the temperature inside the oven. We would suggest replacing the sensor to fix the issue. We hope this solves your problem!
During baking mode the oven shuts down showing a Pf code on display
Hi John, thank you for the question. According to our research, the PF code means power failure. Try powering the oven down at the circuit breaker for 30 minutes, and during this power down check all connections to the control board, then re-power it back up. If this does not help then you may need to replace the control board, part number PS3533908. We hope this helps!
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Hammer 1, Glass range top and heating element 0
22 of 52 peoplefound this instruction helpful.
Richard from CHESAPEAKE, VA
Easy
30 - 60 mins
Screw drivers
Dropped a hammer on the range while removing a ceiling light. Viewed a How-To video on Google. Ordered the needed parts. Followed the steps from the How-To video. Reinstall was a bit tricky by myself - could have used an extra set of hands. I have a few words of caution: 1) Put something between the range top and range - like a
... Read moresheet or drop cloth - to prevent a dropped screw from falling into a crevice in the stove. I dropped a screw and was unable to retrieve it, even with a magnet. 2) Makes sure you remove all bumpers, screws, clips, etc. from the item being replaced and put them on the new item if the new item does not come with replacement bumpers, screws, etc.
Read less
Was this helpful?
Thank you for voting!
No heat in oven mode
8 of 11 peoplefound this instruction helpful.
Dennis from CARY, IL
A Bit Difficult
More than 2 hours
Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Verified P/N with LG. Took a few days . They sent names of several suppliers, cost was almost double. Ordered part from P/S, here in 2 days. Watched video on you tube. Unplugged, took off back, unplugged bake element, removed power box. The opening for bake element is still attached to rear panel by tiny bits of sheet metal. Used Dremel w
... Read moreith cut-off wheel to cut thru nibs & deburr opening. this panel has to be removed, it rests on bottom panel & is held in position by power box. Removed bake element carefully, front of element broken, tried to put new element in, would not fit. Had to grind notches in bottom panel down to clear supports on new element. This did the trick. back together quick & no problems. If had to do again estimate less than 1 hour.. By the way am 81 yrs. young.
Read less
Was this helpful?
Thank you for voting!
Thermostat needed to be replaced
8 of 27 peoplefound this instruction helpful.
Denise from NORTH BEACH, MD
Really Easy
Less than 15 mins
Screw drivers
We had made this determination with the help of a repairman on the phone. I ordered the part and waited for it. It was stuck in West Virginia. After several days after it was expected a repairman fixed my range to the tune of $168. It should have cost $30 (the cost of the part and shipping). Unfortunately I probably won't order
... Read more from PartSelect again.