- Home
- LSC27910SW
- Instructions
LSC27910SW (ASWCLGA) LG Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Broken water line
53 of 72 people
found this instruction helpful.
-
Debbie from FISHER, AR
- Really Easy
- 15 - 30 mins
-
Screw drivers
Remove water filter and water filter holder. Removed cover on back of frig. Removed clip where water line connects to back of water filter. Took half inch wrench pushed in on water line lock to release line. Repeat at other end. Reverse steps to put on new line. Easy repair.
Other Parts Used:
Was this helpful?
Thank you for voting!
Evaporator Fan Squeeking
17 of 21 people
found this instruction helpful.
-
Kyle from WOODBURY, MN
- A Bit Difficult
- 1- 2 hours
-
Screw drivers, Wrench (Adjustable)
Detected noise as coming from top freezer department, and tips and part diagram clearly pointed to evaporator fan. You go in through the freezer (you have to empty top half of freezer); removing the side rails holding the ice bin, and then the 4 outer screws (only 2 each side - not the middle ones) holding the 'auger' that turns the bin
... Read more
. From there it gets interesting in trying to disconnect the wires. You might consider taking some pictures of the connected wires - perhaps it doesn't matter, but several of them can be hooked up in reverse. After the ice marker is out, remove light and light cover, side rails/mounts that hold hold up ice maker. This leaves a large white cover that pops out (seam at bottom of it has two tabs that you can pop out) holding the fan; and then only a few more wires to disconnect to be able to get at the fan. Mine clearly had a wobble to it confirming the source of the squeak and need to replace. Install was just reverse -- a bit tricky to get some of the wires connected given the tight spaces. Overall, not difficult - but a lot of wires and screws to connect/disconnect. I didn't take any pictures as I disassembled, and found myself having to take some extra time to figure it out as I reassembled. In the end -- a silent and functioning refrigerator Good luck!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Water feed line running from water valve to filter housing was leaking
13 of 21 people
found this instruction helpful.
-
Tom from EASTON, PA
- Easy
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
Shut off water supply. Disconnect main supply line. Remove rear lower panel on back of refrigerator. Remove all tubing clamps on back. Disconnect leaking tubing from water supply valve. Remove water filter and unscrew/remove water filter housing. Replace tubing - connect to water filter housing then to water supply valve. Reconnect filter
... Read more
housing and filter. Reinstall lower panel, then main water supply line, then all tubing clamps. Turn water back on and check for leaks after discarding several glasses of water to fill filter. Job complete!
Read less
Was this helpful?
Thank you for voting!
The ice tray had warped and dumped water, which then froze down through the ice bucket and below.
8 of 8 people
found this instruction helpful.
-
George from ATLANTA, GA
- Easy
- Less than 15 mins
-
Screw drivers
To replace the warped tray, I found the service manual (pg. 124 below) which took some interpreting.
Removed the lever. Then removed the assembly by two screws that are forward to the unit and go upwards.
The insulation, sensor, and sensor cover are simply pulled down and off and the unit separated to removed the tray, and ... Read more then insert the new tray. Proceed in reverse. Takes only a few minutes.
/Users/grf/Desktop/fridge ice tray.pdf
Removed the lever. Then removed the assembly by two screws that are forward to the unit and go upwards.
The insulation, sensor, and sensor cover are simply pulled down and off and the unit separated to removed the tray, and ... Read more then insert the new tray. Proceed in reverse. Takes only a few minutes.
/Users/grf/Desktop/fridge ice tray.pdf
Read less
Was this helpful?
Thank you for voting!
Water leaking from back of the refrigerator
8 of 12 people
found this instruction helpful.
-
Jason from PLEASANT HILL, CA
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Pretty simple fix.
1) Removed the screws from lower back plate
2) Removed the screws holding the plastic water lines in place (little plastic brackets - several of them)
3) Take a picture of how the tubing and what hose goes into what part - the 5/16" hose can go into 2 different spots - I didn't do this and I had to ... Read more fix this
4) Pull out the hose "tabs" that lock the clamp into place (several)
5) Push in new hose
6) Put in clamp
7) I had to remove the filter on the inside of the fridge. Remove the filter, there is one screw that comes out, then you will have access to the hose clamps
8) Repeat for all the other hoses
9) Put the plate and brackets back into place (the picture really helps on how to orient and route the 3 different tubes
10) Test the water
11) Crack open a beer for a job well done
Super easy - take a picture! It will save you time!
1) Removed the screws from lower back plate
2) Removed the screws holding the plastic water lines in place (little plastic brackets - several of them)
3) Take a picture of how the tubing and what hose goes into what part - the 5/16" hose can go into 2 different spots - I didn't do this and I had to ... Read more fix this
4) Pull out the hose "tabs" that lock the clamp into place (several)
5) Push in new hose
6) Put in clamp
7) I had to remove the filter on the inside of the fridge. Remove the filter, there is one screw that comes out, then you will have access to the hose clamps
8) Repeat for all the other hoses
9) Put the plate and brackets back into place (the picture really helps on how to orient and route the 3 different tubes
10) Test the water
11) Crack open a beer for a job well done
Super easy - take a picture! It will save you time!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Fridge waterline for ice maker / door water
6 of 8 people
found this instruction helpful.
-
Todd from MARS HILL, NC
- Really Easy
- Less than 15 mins
-
Screw drivers
The heavy work is moving the fridge, then take off the lower plans. Use a bowel or cup for screws and the water line connector spacers so you don't loos them.
undo connections holding water line, including the bottom brakes for the solenoid. Reuse the spring around the lower waterline to prevent external wear on the line.
... Read more r />NOTE: remove the waterline connector spacers and save!
NOTE: you must compress (not pull) the connect to then pull the waterline out of the connectors.
NOTE: You must also remove the water filter and housing inside the fridge but this is easy.
MOTE: Test the line for leaks by turning on the water and then using the door water. The filter will need to refill so it may take a minute before water comes up. This line only have pressure when the door water is used or the ice maker needs to make ice.
After replacing the line, test the line for leaks by using the door water so the solenoid fills the lines
undo connections holding water line, including the bottom brakes for the solenoid. Reuse the spring around the lower waterline to prevent external wear on the line.
... Read more r />NOTE: remove the waterline connector spacers and save!
NOTE: you must compress (not pull) the connect to then pull the waterline out of the connectors.
NOTE: You must also remove the water filter and housing inside the fridge but this is easy.
MOTE: Test the line for leaks by turning on the water and then using the door water. The filter will need to refill so it may take a minute before water comes up. This line only have pressure when the door water is used or the ice maker needs to make ice.
After replacing the line, test the line for leaks by using the door water so the solenoid fills the lines
Read less
Was this helpful?
Thank you for voting!
Changing out the Ice Maker tube
9 of 19 people
found this instruction helpful.
-
HARRY from SPARKS, NV
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
An easy way to get a refrigerator out from the wall is to use a tow strap or 1/2 to 3/4 in. rope. Throw a loop behind refer while keeping both ends in your hands. Let it settle down to the lower half of unit and pull using both hands. Comes right out.
Remove lower panel. Unscrew water valve from cabinet. Remove all tube holders L ... Read more ay some rags down to catch a little water drainage.
Turn off water supply valve at wall. Unplug Power. Remove filter and filter holder. (one screw).
remove tube from valve by removing plastic C clip. Push plastic ring towards the valve and pull out tube at same time.
With the tube free, remove filter, then mount screw to remove the inside filter holder. When it is out, pull the tube doing the same process as the lower end. Pull tube out and replace with new one putting everything back in reverse order.
Before placing tube holders back on, turn on water to check for leaks.
After turning water back on and plugging in power, push refer back into place.
While I was there, I also replaced the hose from the wall to the refer.
Remove lower panel. Unscrew water valve from cabinet. Remove all tube holders L ... Read more ay some rags down to catch a little water drainage.
Turn off water supply valve at wall. Unplug Power. Remove filter and filter holder. (one screw).
remove tube from valve by removing plastic C clip. Push plastic ring towards the valve and pull out tube at same time.
With the tube free, remove filter, then mount screw to remove the inside filter holder. When it is out, pull the tube doing the same process as the lower end. Pull tube out and replace with new one putting everything back in reverse order.
Before placing tube holders back on, turn on water to check for leaks.
After turning water back on and plugging in power, push refer back into place.
While I was there, I also replaced the hose from the wall to the refer.
Read less
Was this helpful?
Thank you for voting!
Broken Guide Rail
4 of 6 people
found this instruction helpful.
-
Nicole from BROOKSVILLE, FL
- Very Easy
- Less than 15 mins
-
Screw drivers
This site was awesome! I was able to very quickly look up my refrigerator model, find the proper part number, and order the part. The only suggestion I would make is to update the cut sheet with a more clear version, it was a little difficult to make out the part number because the scan/drawing was fuzzy, but I was still able to make it
... Read more
out. Got the part in the mail very quickly and it was super easy to remove the old rail and install the new one. Take out the screws from the old one, remove the old rail, line up the holes, install the new one, and put back the screws. It's so nice to have a site like this to fine parts and order them! Too cool! Thank you so much!
Read less
Was this helpful?
Thank you for voting!
Brocken rails
3 of 4 people
found this instruction helpful.
-
Jose from PHOENIX, AZ
- Very Easy
- Less than 15 mins
Very easy to replace right and left rail 3 screws on each side
Other Parts Used:
Was this helpful?
Thank you for voting!
Water had reached its recommended service life..
4 of 7 people
found this instruction helpful.
-
Willard from COMPTON, CA
- Really Easy
- Less than 15 mins
Closed valve to water supply line; Removed contents of top shelf. Removed top shelf by sliding it out. Unscrewed old water filter and screwed in new filter. Replaced to shelf and contents in reverse order. Opened water supply line.
Was this helpful?
Thank you for voting!
Refrigerator did not run. It made several rapid clicks, then silent, then a minute later more clicks.
3 of 4 people
found this instruction helpful.
-
John from OCEAN SPRINGS, MS
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers
I removed the lower back panel. The difficulty and time consuming part was finding the old parts. They were inside a cover on the side of the motor. The cover was difficult to remove. It slides away from the motor. The terminals on the replacement parts were oriented differently from the original, Like a mirror image. Accordingly,
... Read more
I reversed the wires (side to side) and connected them to the replacement parts. The refrigerator is now working fine.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Fan Blade Loose
3 of 5 people
found this instruction helpful.
-
Kyle from NEW ORLEANS, LA
- Very Difficult
- More than 2 hours
I paid for the expedited shipping and they sent me a cheap knockoff attempt at the part that had the wrong size hole. So they refunded me the money I paid for the part but not the shipping, and then I crushed the part they sent me with a hammer and threw it away.
Was this helpful?
Thank you for voting!
whater valve whith a defected selenoid and water leaks.
2 of 2 people
found this instruction helpful.
-
Albert from NORTHRIDGE, CA
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set, Wrench set
First ,I unplug the refrigerator .
2nd i remove the back cover, clean the dust.
3th disconnect the water line, remove the all valve..
4th unplug all the wires and code ea with a No,remove the water lines
5th replace the valve reconnect the wires and water lines.replace the
back cover at last screw back the w ... Read more ater line.check for water leaks .
i found ease the valve replacement installation.
.Thanks for the video.
2nd i remove the back cover, clean the dust.
3th disconnect the water line, remove the all valve..
4th unplug all the wires and code ea with a No,remove the water lines
5th replace the valve reconnect the wires and water lines.replace the
back cover at last screw back the w ... Read more ater line.check for water leaks .
i found ease the valve replacement installation.
.Thanks for the video.
Read less
Was this helpful?
Thank you for voting!
Replaced hose and it was exactly what I needed.
3 of 5 people
found this instruction helpful.
-
Donald from CLEBURNE, TX
- Very Easy
- 30 - 60 mins
-
Screw drivers
Replaced old hose and installed the new one. Was very simple with the instructions in your email..... step by step, could not of been any similar.... you guys rock
Was this helpful?
Thank you for voting!
Right side door creaky squeaky annoying
3 of 5 people
found this instruction helpful.
-
Chris from MURFREESBORO, TN
- Easy
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
Took off door per normal instructions.
Removed the old stopper and hinge assembly (the hard rubbery parts had worn enough against each other to cause the annoying sound when opening and closing the door).
Inserted the new stopper and hinge assembly.
There was no locking nut on the newer part, so just had to level the fridge ... Read more door without that part of the instructions (from normal LG instructions)
Overall easy for a non-handy person and the annoying sound is gone.
Wife is happier now.
Removed the old stopper and hinge assembly (the hard rubbery parts had worn enough against each other to cause the annoying sound when opening and closing the door).
Inserted the new stopper and hinge assembly.
There was no locking nut on the newer part, so just had to level the fridge ... Read more door without that part of the instructions (from normal LG instructions)
Overall easy for a non-handy person and the annoying sound is gone.
Wife is happier now.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!