LSC26905SW (ASWCLGA) LG Refrigerator - Instructions

Detected noise as coming from top freezer department, and tips and part diagram clearly pointed to evaporator fan. You go in through the freezer (you have to empty top half of freezer); removing the side rails holding the ice bin, and then the 4 outer screws (only 2 each side - not the middle ones) holding the 'auger' that turns the bin ... Read more . From there it gets interesting in trying to disconnect the wires. You might consider taking some pictures of the connected wires - perhaps it doesn't matter, but several of them can be hooked up in reverse. After the ice marker is out, remove light and light cover, side rails/mounts that hold hold up ice maker. This leaves a large white cover that pops out (seam at bottom of it has two tabs that you can pop out) holding the fan; and then only a few more wires to disconnect to be able to get at the fan. Mine clearly had a wobble to it confirming the source of the squeak and need to replace. Install was just reverse -- a bit tricky to get some of the wires connected given the tight spaces. Overall, not difficult - but a lot of wires and screws to connect/disconnect. I didn't take any pictures as I disassembled, and found myself having to take some extra time to figure it out as I reassembled. In the end -- a silent and functioning refrigerator Good luck!

To replace the warped tray, I found the service manual (pg. 124 below) which took some interpreting.
Removed the lever. Then removed the assembly by two screws that are forward to the unit and go upwards.
The insulation, sensor, and sensor cover are simply pulled down and off and the unit separated to removed the tray, and ... Read more then insert the new tray. Proceed in reverse. Takes only a few minutes.

/Users/grf/Desktop/fridge ice tray.pdf

This site was awesome! I was able to very quickly look up my refrigerator model, find the proper part number, and order the part. The only suggestion I would make is to update the cut sheet with a more clear version, it was a little difficult to make out the part number because the scan/drawing was fuzzy, but I was still able to make it ... Read more out. Got the part in the mail very quickly and it was super easy to remove the old rail and install the new one. Take out the screws from the old one, remove the old rail, line up the holes, install the new one, and put back the screws. It's so nice to have a site like this to fine parts and order them! Too cool! Thank you so much!

Very easy to replace right and left rail 3 screws on each side

I removed the lower back panel. The difficulty and time consuming part was finding the old parts. They were inside a cover on the side of the motor. The cover was difficult to remove. It slides away from the motor. The terminals on the replacement parts were oriented differently from the original, Like a mirror image. Accordingly, ... Read more I reversed the wires (side to side) and connected them to the replacement parts. The refrigerator is now working fine.

I paid for the expedited shipping and they sent me a cheap knockoff attempt at the part that had the wrong size hole. So they refunded me the money I paid for the part but not the shipping, and then I crushed the part they sent me with a hammer and threw it away.

First ,I unplug the refrigerator .
2nd i remove the back cover, clean the dust.
3th disconnect the water line, remove the all valve..
4th unplug all the wires and code ea with a No,remove the water lines
5th replace the valve reconnect the wires and water lines.replace the
back cover at last screw back the w ... Read more ater line.check for water leaks .
i found ease the valve replacement installation.
.Thanks for the video.

Really Easy

Replaced water pump assembly, all compression fittings easy to put together

I am a woman and I did this in about 10 mins. I turned off the water, disconnected the water line, took the back off the fridge, disconnected the motor plug and unscrewed the fan. It took a little maneuvering to get the fan out but once I did it was a breeze. Opened up back door that housed the motor, took the motor out and put in the new ... Read more one. Put everything back together and it's working great. Very fast shipping so don't pay for the expedited way to ship. I ordered Sunday night and it was in my door by 10:00 Tuesday morning.

Just replaced the old shelves with new

It was a "snap to complete it" inasmuch as the part just snapped in.

Remove two screws on top of the fridge; removed old switch and inserted new switch. Worked like a charm. Replace casing and screws.

Removed shelf that rails were mounted to. Used a std phillips screwdriver to loosen screws attaching the rails, three per side. Removed damaged rails, lined up new rails and tightened screws. Returned shelf to refrigerator and inserted tray on the new rails.

Simply removed the drawer, then removed the shelf above which held the guides, removed the guides ( 3 screws per side )and replaced them.