LS33CC ((24BL59M5710)(2015)) Cub Cadet Log Splitter - Parts

The Push Cap is a black plastic cap which secures to the end of a shaft to prevent injury. It can be installed with a hammer and is rated as "Easy" to install. If the part appears damaged or worn down in a way that could cause injury, it should be replaced. Refer to your make, model and diagrams to check if this is the right part for you.

This OEM Hub Cap, or Dust Cap, is a 2-inch, silver, steel part, sold individually. It requires a Rubber Mallet to install and its installation is rated as Easy by our customers. This part attaches inside the wheel on the hub, and is used to keep dirt out of the hub. It must be replaced when damaged or missing (if it is damaged it will b...Read moree out of round, and will not fit). Check your model number to ensure you are purchasing the correct part.

This mounting bolt seals the fuel system and keeps the fuel bolt securely attached to the carburetor in a variety of gas-powered outdoor equipment. It is a genuine OEM part made of metal with dimensions of 0.25-20 x 0.875 inches. If you notice that the bolt is corroded or rusted, it will need to be replaced. A faulty or loose mounting bol...Read moret may cause fuel to leak, make it difficult to start or run your equipment engine, and may allow contaminants to enter the engine. The bolt is easy to install using a wrench or socket. Be careful not to overtighten the bolt as this may damage the fuel bowl. Each item is sold individually.

This grease seal, also known as an oil seal or a shaft seal, in your log splitter or chipper shredder serves as a protective barrier. It keeps lubrication inside the bearings and stops dirt from entering them. It is commonly located in the wheel hubs or axle assemblies of your machine. A broken grease seal leads to contaminated bearings. ...Read moreYour machine will then undertake more friction and can overheat, reducing its performance. You will need a seal puller or a flathead screwdriver to pry a grease seal out of your machine. When installing the new grease seal, apply a thin layer of lubricant to its inner surface before pressing it into its housing. Please be informed that this OEM-certified component is sold individually.

It is a genuine item that is supplied directly by the original equipment manufacturer for use with lawn and garden equipment. The cam actuates rocker arms that press down on the valves, opening them. This is a high-quality replacement for a missing or a damaged arm-rocker that was originally installed on a new unit. Please make sure to ch...Read moreeck the appropriate diagrams of your model for the correct location and application of this part. Keep in mind this high-quality rocker arm is made of durable metal and is sold individually. A wrench set will be needed to take the engine apart when performing this repair.

This genuine part is a M6-1 x 12 Grade 8.8 mounting bolt that is zinc-plated. It is used to secure parts of your machine together, keeping these components tightly attached to each other so that they do not budge during operation. In lawn equipment, this bolt is usually used to attach the engine to the housing of the machine, but you may ...Read morealso find it in other areas of the machine. If the bolt rattles when you shake it, even when tightened, it is time to replace it. It must also be changed if it is corroded or bent, or else it may damage the components it is holding together. You will need to remove this mounting bolt with a socket wrench. This part is sold separately, so it is important to consult your user manual to understand how many bolts your machine needs. If you were initially replacing one bolt on your machine, you should consider purchasing more, as these bolts wear out at the same rate and you may end up needing to replace multiple bolts at once.

A breather hose is used within the ventilation system for a crankcase, or engine, to connect the crankcase to the air manifold and allow hot air to escape. This genuine OEM breather hose is made of a high-quality rubber and is designed for use and compatible with several different makes and types of outdoor power equipment, such as lawnmo...Read morewers, tillers, engines, log splitters, and snowblowers. Due to the build material of this hose, it can break down over time and through exposure to gas, oil and excessive heat. If you notice any damage on the hose, fuel leaks or worsened engine performance resulting in rough idling or stalling, this hose may be damaged or simply need replacing. To replace this hose, locate the hose on your model and remove any clamps, before pulling off the old hose and installing the new, with any necessary hardware such as clamps.