LS1220 Makita Miter Saw - Parts

This Kerf board is a genuine Makita replacement part. It is made of rigid plastic and has 2 screw holes, one at either end, to secure it to your saw. rnrnKerf boards (also called kerf plates) are used to prevent excessive splintering, resulting in cleaner cuts. Using the wrong kerf board for your tool can give a rough edge to the material you're cutting.

Genuine Manufacturer Sourced replacement part used on a variety of Makita Power Tools. This is a Metal Pan-Head Screw and it is sold individually. This screws is commonly used to hold two pieces of Housing Set together.

This is a genuine Makita replacement part that includes two carbon brushes with wire leads attached. Carbon brushes are essential components in power tools and are among the most commonly replaced parts due to regular wear from friction. Over time, worn brushes can cause a motor to run poorly, operate intermittently, or lose electric brak...Read moreing power. Replacing them can often restore your tool’s performance. A worn brush may appear cracked, pitted, burned, or worn down near the wire lead. It’s always best to replace both brushes at the same time, even if only one shows signs of wear. When installing new brushes, be sure to inspect the armature for any damage such as burns or cracks, which could indicate more serious motor issues.

This replacement tapping screw is an authentic item that is supplied by the original manufacturer for use with Makita power tools. It is a standard hardware which has multiple applications depending on the model of your unit, please make sure to check appropriate diagrams for correct location and use of this part. This high-quality phillips pan-head screw is made of durable metal and it is sold individually.

This cord is a genuine Makita replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Over time, power tool cords will wear out or become frayed. We recommend replacing a cord as soon as signs of wear are visible. Power Cord Specifications: • 2 Prongs • 2 Wires • 14 Gauge • 8 Feet Long

This replacement pin is an authentic OEM component which is made for use with Makita equipment. The pin is generally utilized to secure a part while allowing it to rotate freely. It is a standard hardware which may have multiple applications. Make sure to refer to the appropriate diagrams of your model for the exact location and the corre...Read morect installation of this pin. One durable metal item is included. You may need a screwdriver to take the unit apart when replacing this pin.

Included in Part Number 516306-1. rnThis Ball Bearing is sealed on both sides. This genuine Makita replacement part is sold individually. rnrn • Ball bearings minimize friction between rotating parts in your tool. The balls or rollers bear the load and spin, distributing the weight evenly, while the minimal contact area of the balls re...Read moreduces friction. This reduces wear on the tool, allowing it to run smoothly. rn • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

This is a genuine OEM replacement part sourced directly from manufacturer. It is connected to the arm holder and it allows you to lock the saw in the needed position. This lever is made out of black plastic and it is sold individually. You would need a screwdriver to remove the screw that secures this lever.

Genuine Makita replacement part, this item is sold individually. The purpose of the Brush Holder Cap is to retain the brush in the brush holder. This Brush Cap is used on all the Makita models listed below. It is removed by using a slotted screwdriver Do not press too hard when removing the cap they do have a tendency to break.

This item is available as an individual replacement part. The strain relief attaches to the gear housing. When replacing this item a screwdriver may be needed. It is made of plastic and will require replacing if it breaks. This is a genuine replacement part sourced from the original manufacturer for use with jointers, planers, and saws made by Makita.

It is a genuine item that is supplied by the original equipment manufacturer for use with Makita saws. This is an identical replacement for a missing or a faulty bolt that was installed on a new unit, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this high-quality item is made of durable metal and is sold individually.