LS12 - Parts

This is a Ball Bearing that is sealed on both sides. This is a genuine Makita replacement part that is sold individually. • Ball bearings minimize friction between 2 parts in your tool that would otherwise spin and rub against each other. The balls or rollers take the load and spin, distributing the weight evenly while the minimal ...Read morecontact area of the balls reduce friction. This reduces wear on the tool and allows it to run smoothly. • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

This authentic replacement ball bearing is supplied directly from the original equipment manufacturer for use with Makita power tools. Ball bearings are used to reduce friction between rotating parts, please make sure to refer to the appropriate diagrams of your unit for the correct location and use of this component. Over time the roller...Read mores may wear out and begin to fail eventually requiring a replacement to ensure the peak performance. It is made of high-quality steel and it is sold individually.

O-rings are designed to contain thousands of pounds of pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes for O-Ring failure, such as pressure, friction, temperature or chemicals. The most common are: • Extrusion and Nibbling O-rin...Read moreg has ragged, tattered edges. These are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • Abrasion One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that is too rough, contains grit or is too smooth to allow lubrication. • Over Compression O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • Heat Hardening O-ring has a pitted or cracked surface, and often is flattened on both sides. Caused by temperature exceeding o-ring capacity. • Weather/Ozone Cracking O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching causes similar cracking.

This steel ball is an OEM replacement part supplied directly from Makita. It is crafted for use with various machines, including miter saws and demolition hammers. This steel ball has many different functions depending on the machinery it is being used in. Please refer to the owner's manual for specific replacement recommendations. It is ...Read moremade of steel and sold individually. The compression spring (part 231038-6) is sold separately.

This is a genuine replacement part sourced from the original manufacturer for use with screwdrivers, drills, saws, and nailers made by Makita. The steel ball goes between two cams and is made of metal. An allen wrench might be required during the replacement of this item. It will require replacing if it becomes lost since it is a very small part. This is available as an individual replacement part.

This is an original OEM part. The Makita flange 53 is made of metal, and is compatible with several saw devices. This part is fastened between the hex. flange head bolt and the ring 15.8, and assists in securing the TCT saw blade. Please refer to manual and diagrams for specific instructions. This item is sold individually. A wrench and a screwdriver are helpful in making the repair.

This is an OEM part sourced directly from the manufacturer. The inner flange is designed for use in Makita miter saws. This part is made of metal, and is used to help hold the saw blade in place. You will require a wrench when replacing this part. This item is sold individually.

This is an authentic Makita replacement part that has been sourced from the original manufacturer to be used with miter saws. The metal flange is used to disperse pressure put on the saw blade by the flange head bolt across a wider area that matches the inner flange. This item is available as an individual replacement part. A hex socket wrench is needed to install the flange.

This replacement dust bag is specially manufactured for use with Makita miter saws and planers. The purpose of the bag is to collect the dust and trimmings when using. Keep in mind this high-quality component is made of durable fabric material and it is sold individually.