Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Door light switch, 3rd one I have replaced in 6 years made in China.
1 personfound this instruction helpful.
Charles from CURWENSVILLE, PA
Really Easy
Less than 15 mins
Pliers, Screw drivers
Easy install, small screwdriver under back of old switch push out and pull out with small pliers. unsnap the old plug and install new. YOUR DONE
Was this helpful?
Thank you for voting!
Replace switch
1 personfound this instruction helpful.
Dean from HILLSDALE, MI
Really Easy
Less than 15 mins
Screw drivers
Read previous tips Taped off area around switch to protect surface Used putty knife to extract switch Used screwdriver to separate connector from switch Plugged in connector Pushed switch assembly into opening Removed tape
Was this helpful?
Thank you for voting!
door slight switch failed
1 personfound this instruction helpful.
Greg from CASA GRANDE, AZ
Really Easy
Less than 15 mins
Pliers
Covered the sidewall with tape to protect. Pried the switch out with knife blade and removed electric plug with needle nose pliers. placed plug in new switch and pushed switch into the hole in the side wall. Took about five minutes.
Unplug from wall receptacle. Pry switch out with screwdriver while pushing on inner tab. Then disconnect electrical plug.
Was this helpful?
Thank you for voting!
Replace the light switch for the refrigerator
1 of 2 peoplefound this instruction helpful.
Karyn from DURHAM, NH
Really Easy
Less than 15 mins
Cover the putty knife with tape so you do not scratch the side wall where the switch is located. Slide the knife under the edge of the switch and push in a bit towards the switch and slightly twist to pop the switch out of its hole. Disconnect the wires from the switch and simply plug in the new switch. Push wiring back into the hole and
... Read morecareful push the switch into the hole until it snaps into place.
Read less
Was this helpful?
Thank you for voting!
the light did not work when door was opened. At first it would flicker then off completely.
1 of 2 peoplefound this instruction helpful.
Alma from Winterport, ME
Very Easy
Less than 15 mins
Screw drivers
My son just pried out the old switch with a screw driver snapped out the old one and snapped in the new one. Pretty sure even I could have done this. Very quick and easy. Thanks. :-)
Was this helpful?
Thank you for voting!
Refrigerator light had a short in it and would randomly work
1 of 3 peoplefound this instruction helpful.
Tammy from HAGERSTOWN, MD
Very Easy
Less than 15 mins
Screw drivers
Unplugged the fridge. Used a screwdriver to loosen the switch. Easy to disconnect from fridge and just plugged the new switch in. Popped right back into the side of the fridge and worked perfectly.
Was this helpful?
Thank you for voting!
Unit kept beeping as if the freezer door was open
0 of 1 peoplefound this instruction helpful.
Paul from San Jose, CA
Really Easy
Less than 15 mins
Pliers
I popped the old switch out of place and then disconnected the wire harness from the switch with a pair of needle nose pliers. I then inserted the harness into the new switch and popped the switch into place. Super easy and fast.
Was this helpful?
Thank you for voting!
water supply to ice maker leaked
0 of 1 peoplefound this instruction helpful.
john from locust valley, NY
Really Easy
Less than 15 mins
Screw drivers
Gave model number on website, found picture of icemaker section. Ordered part that came in 3 days and switched old for new
Was this helpful?
Thank you for voting!
light out
0 of 1 peoplefound this instruction helpful.
Jack from Ellenton, FL
Easy
Less than 15 mins
Screw drivers
slid screw driver under edge of switch, easy.
Was this helpful?
Thank you for voting!
The water line was leaking
0 of 1 peoplefound this instruction helpful.
Awilda from Staten Island, NY
Easy
15 - 30 mins
Screw drivers
Removed the damaged tube and replaced the it with a new one.
Was this helpful?
Thank you for voting!
Water/ice maker not working
9 of 38 peoplefound this instruction helpful.
Brent from ROGERS, MN
Really Easy
Less than 15 mins
Screw drivers
Remove push plate for water/ice maker switch, remove 2 screws and 2 wires for switch. Replace with new.
Was this helpful?
Thank you for voting!
Ice cubes did not drop out of tray when the ice maker cycled
Michael from Eagle, WI
Easy
15 - 30 mins
Screw drivers
1) Take out 3 screws from top of icemaker. 2) Unplug electrical connector from wiring harness. 3) Remove icemaker unit from freezer and then remove frozen cube sensor with clip and rear insulation. 4) With your hands pull cube tray motor out of the holding clips with the tray- if this is too difficult, spread bracket and only remove the t
... Read moreray from the unit. 5) Insert new tray into slots and install new or existing ice sensor, insulation, and sensor clip. 6) Reinstall icemaker unit to ceiling of freezer, don't forget to plug into wiring harness. 7) Turn unit on and make some ice!
Each time we've had to move we have to remove the doors from the fridge to get it thru the front door.since water and ice run thru the freezer door there are 2 tubes that connect at the bottom of the freezer door that aren't meant to be separated very often if ever.it's easier to cut the tubing on b
Sarah from Elk Grove, CA
A Bit Difficult
15 - 30 mins
Pliers
With alot of elbow grease and a pair of pliars we managed to get the old connector off wo cuttig the tubing as the tubing was getting to short from being cut once to many times & there was no more play in the length.Original connector was a different color and shapped slightly different than the new one so was a bit concerned that I had
... Read moreordered the wrong part but it went one very easily & did not leak. We even managed to remove it again just to see if it was possible wo cutting again. it came off with no trouble.I would say the replacement part was a better fit than the original simply because we could remove it easily wo having to cut the tube!
My Orders
