LRFD25850ST (00) LG Refrigerator - Instructions

Video makes it look easy. Kenmore refrigerator does not have "groove" along the right hand side of switch that allows for pushing down on release. Used a thin screwdriver to get under to push while holding switch edge with pliers. Kept slipping. Tape sides to avoid scratching inside of refrigerator.

Turn off power, remove upper and lower drawers (may need to open upper refrigerator doors to remove large freezer bin,) remove drawer supports (upper and lower), remove rear freezer panel (trick is to loosen 4 screws on fan bumpout to get the panel to come free from the freezer side wall), test thermistor with multimeter (should have cont ... Read more inuity or near zero resistance across 2 orange fuse wires) before cutting zip ties, cut zip ties holding Thermistor in place, remove old Thermistor, install new Thermistor, install new zip ties, replace rear freezer panel, install upper and lower drawer supports, install drawers, turn on power, should be fixed if error code doesn't return after 6 hours.

Ordered a new tank assembly, but the new part also leaked because it had a hole in it. Ordered another that worked fine. Used a flat head screwdriver to remove the clips covering the screw holes to the tank assembly cover, then a phillips to remove the cover screws and the screws retaining the tank. Did not use the tubing that came wit ... Read more h the new tank (removed it by taking out the neck clip then simultaneously pushing back on the neck piece while pulling out the hose). Used this same procedure to remove the old tank at both positions. Installed the new tank, replaced the clips, pressurized/tested the system and put the cover back on. Overall less than a 5 minute job...except for the extra week waiting for a good part.

Shut off water supply. Disconnect main supply line. Remove rear lower panel on back of refrigerator. Remove all tubing clamps on back. Disconnect leaking tubing from water supply valve. Remove water filter and unscrew/remove water filter housing. Replace tubing - connect to water filter housing then to water supply valve. Reconnect filter ... Read more housing and filter. Reinstall lower panel, then main water supply line, then all tubing clamps. Turn water back on and check for leaks after discarding several glasses of water to fill filter. Job complete!

Lower shelf frame lifted right off w/o the use of any tools. Removed both drawer cover fronts.The glass shelf which sits on top of frame over time will tend to stick to shelf frame. Running Hot water over glass dissolved stickiness and glass separated easily.Do Not try and pry apart if it seems stuck to shelf frame!. It may crack!. Cleane ... Read more d all parts, and replaced both drawer front covers. Put shelf frame back in on shelf holder. Done. Approx.20 minute repair w/o any problems.

The replacement was the exact size,easy installation.

The refrigerator had the above code and when I check on YouTube, it explained that the defrosting was not working properly. It was taking more than 80 minutes to defrost. I ordered the Temperature Sensor first and it was not the issue. I also ordered the Defrost Temperature fuse or the Thermistor. I had to defrost the refrigerator first ... Read more by using a portable heater to get it done quickly. (See Youtube on how to get to the Defrosting Unit inside the freezer). The Thermistor was the wrong part. I called the Partselect and explained that the part with the heating element is one piece. (Heating Coil Thermistor or Heating Coil). By replacing that piece solved the Error Code issue. I listened to Youtube for the instructions on how to replace the Heater Coil. So if you see the Error Code dH F, you need to replace the Heating Coil, which comes in
one piece and sits on the bottom of the Defrost Element.

Be sure to keep all the parts from the old frame because, first, you have to attach the metal stiffener/support bar from the old to the new. Care is necessary trying to fit the upper pop-up drawer doors and the clear plastic drawer tops to the frame. The hinges of the door top are plastic and could break, causing you to have order another ... Read more part. The clear plastic tops, under the glass the shelf, do not fit intuitively and you have to make sure they fit in the right direction. Along one edge is a 1" square spot; that goes to the back of the frame. Then, you need to be careful snapping them into place so you don't break the supports. Once you have all the parts on in the right places, then it's just a matter of sliding everything into place in the refrigerator.

As per utube

The replacement part came in a timely manner and snapped right into place.

The heavy work is moving the fridge, then take off the lower plans. Use a bowel or cup for screws and the water line connector spacers so you don't loos them.
undo connections holding water line, including the bottom brakes for the solenoid. Reuse the spring around the lower waterline to prevent external wear on the line.
... Read more r />NOTE: remove the waterline connector spacers and save!
NOTE: you must compress (not pull) the connect to then pull the waterline out of the connectors.
NOTE: You must also remove the water filter and housing inside the fridge but this is easy.
MOTE: Test the line for leaks by turning on the water and then using the door water. The filter will need to refill so it may take a minute before water comes up. This line only have pressure when the door water is used or the ice maker needs to make ice.


After replacing the line, test the line for leaks by using the door water so the solenoid fills the lines

Read less