LRFD22850ST (ASTCGSZ) LG Refrigerator - Instructions

easy, a screw driver repaired in a mintue

slid screw driver under edge of switch, easy.

I popped the old switch out of place and then disconnected the wire harness from the switch with a pair of needle nose pliers. I then inserted the harness into the new switch and popped the switch into place. Super easy and fast.

I was told the mother board went out. Took a few months to finally get one myself after repairman didn't come through. It turned out not to be the motherboard that sears repairman tested it for and said that's what it needed. I found Parts select after going round and round with sears parts refusing to accept return. There prices were be ... Read more tter, as well as shipping and it came so quick i thought it was over night. The controller assembly was not the problem so we have it for a spare now. It was the freezer fan but even after installing it nothing would work is why we ordered the controller assembly. after 2 days and about 7 hours of checking, taking apart, rechecking assembling by my determined electrician it turned out to be a loose wire. LOL hope this helps someone. I'm just glad to have my fridge again! Blessings!!!

Uncoupled the old connector, replaced with new connector and attached supply line. Repair easy with right part, prior to ordering the right part I had tried a compression fitting and it still leaked. U-tube and others demonstrating repair assured me I was on the right path.

Remove push plate for water/ice maker switch, remove 2 screws and 2 wires for switch. Replace with new.

Changed door switch. Repair worked for a few days but re-occured. Possibly the other switch is bad .

One Philips screwdriver. The correct part arrived in less than 24 hours. Great service

Lifted the old one out, set the new one in!

Tape off the light button so door alarm does not go off. Take off the clear light shield and remove the light bulbs. Be careful, bulbs may still be HOT!! With Phillips head screw driver unscrew the light plate assy. Drop it down in a comfortable position. Disconnect the connector, unscrew the thermal sensor and remove light assy. Install ... Read more new light assy into light plate assy. There is no thermal senor in the new assy. Snap light plate assy back into place and install the two screws previously taken out. Install bulbs and clear cover. Remove tape from light door switches and you are done. Lights should go on and off when door buttons are pushed in and out.

looked up on google for lg refridgerator replacement parts, found parts select, went to their web site and found the exploded view of my refridgerator called them and ordered the parts necessary. they shipped them very fast and have great cusomer service. I will use them again if i need a part for an apliance.

I could not figure out from the online manual just what to do or what part to order as the pictures of parts were so small. I had to call the company and explain what happened. You sent the gasket holder that I needed. I had to call my handy man to install. It did not take him toof long to figure out what to do.

Gasket held in place by plastic bezel. Remove bezel by carefully pulling it toward you. Held in place by plastic clips. May need to pry carefully near clips. Pull gasket away from front edge of door. Gasket holder held by plastic swivel pieces top and bottom. Snap these out. Slide the gasket holder off the gasket. Remove the scre ... Read more ws and slip the metal rod out of the broken holder. Retain screws, plastic clips, and cam. Slide the rod into new holder adding plastic clips and cam. Replace screws. Slide holder back onto gasket. Snap plastic clips into slots, being careful to bend the springs back so they go into the channel. Replace bezel. See videos on replacing door gaskets.

Real Easy

There is a part called a "cam" on my 23cuft french door refrigerator. It is at the top of both doors and works to keep the closed door from popping open when slamming shut the opposite door. Twice in 2 years this cam has broken off of the long plastic strip which is the gasket holder. Both times on the right door. The repair is easy, b ... Read more ut you have to be careful not to break the plastic pieces. First, you have to remove the trim piece covering the gasket strip (233D in the diagram). It pulls out only one way -- toward the SIDE of the door (rather than inwards towards the fridge). Next, you have to remove the entire gasket around the door; it pulls out very easily. Third, there are 2 plastic hinges which snap into the door frame; to remove it use a screwdriver and gently pry it to the side of the door (rather than towards the center of the fridge or away from it). Frankly, that's the hardest part - taking it all apart without breaking the trim piece. When I first had it repaired under warranty, the repairman brought an extra trim piece (233D) in case he broke it when he removed it. But it simply snaps in place so you should be okay if you are careful when prying it out.